Klein Tools VDV826-729 Pass-Thru Modular Data Plugs, RJ45-CAT6, 10-Pack, Gold Plated, Power Over Ethernet-FCC-RoHS Compliant, For Solid or Stranded Cable

I recently used the Klein Tools Pass-Thru Data Plugs (Cat6) for a home network installation, and they exceeded my expectations. As someone who frequently works on network setups, I’ve found that these pass-through plugs are a game-changer. The design allows the wires to pass all the way through the connector, making it easy to verify correct wiring before crimping. This feature alone saves a ton of time and frustration compared to traditional plugs.The build quality of these connectors is excellent. They’re durable, secure, and designed to handle high-speed Cat6 data transfers without any performance issues. The connection quality is outstanding—no drops or interference, and the data transfer speeds have been top-tier since using these plugs.Additionally, the compatibility with Klein’s pass-through crimper ensures a clean, professional cut every time. No more guessing or trimming extra wires after crimping!If you’re looking for dependable, high-quality data plugs that streamline the entire installation process, these Klein Tools Pass-Thru Data Plugs are a must-have. They make setting up Ethernet cables easy and efficient, and the end result is flawless. Highly recommend for both professionals and DIYers!

I had câbles that just wouldn’t make a good connection. Crimped and re-crimped. Then I found these connectors. They work every time, and easy to align for cat 6 and cat 6a cables.

Update: As it is cat 6 and these do fit cat 6 receptacles, I am changing the rating.These are easy to use and make verification that your wires are where they should be. Unfortunately, these don't fit AT&T wireless modems or Unifi wireless U6+ APs or the UCG max ports. There is a little nose on the connector that prevents the terminal from inserting completely. They do fit in the keystone ports (iwillink), so all is not lost.Your mileage may vary. I should have done more research on the connector before buying.

I used these successfully with Cat6, UTP, outdoor rated cable. I've made probably a dozen connectors and had no failures, though a few of them took several tries. That probably speaks more to my skill than to the quality of the connectors. You do have to take a lot of care to have the wires lined up perfectly and very straight before trying to push them through, otherwise they bend or go in wrong.However, I just purchased some Microconnectors shielded outdoor rated Cat6 (F/UTP) and it seems the conductors on this cable are just a bit larger. It's pretty much impossible to get these into the connectors. Others have reported similar problems. It seems that there's some variation among the outdoor rated Cat6 - especially the shielded varieties, and some are just too big for these.It would be good if Klein reported which brands their connectors are compatible with but I haven't seen anything to date. I just ordered some connectors direct from Microconnectors that are specifically intended for this cable.

These pass-thru connectors are way better than traditional crimped connectors. Along with the Klein pass-thru crimp tool, these will save you time and effort.

these are more expensive, but they did seem to work better than the cheaper ones I purchased. More consistent contact after crimping - which was my previous problem while making some cables. I would crimp them and then they wouldn't work or have intermittent signals.

Works as advertised. These are the proper plugs to use with the Klein pass-thru crimper and they were simple to use and worked perfectly. A bit pricey, but much easier to use than non pass-thru plugs where you have to separate and trim all of the wires accurately to avoid shorts and opens. These are all I will use in the future.

Very good for the DIY’er who needs the ‘pass thru’ type of connector. This allows you to strip the outside insulation off, untwist the 4 pairs, and then place them in correct order to slide in the connector. This allows you to pull the entire thing onto the outside insulation and crimp into place. Small diagonal cutters are needed to trim all the ends flush to the connector and you’re good to go.