Bella Bidet Solid Brass Metal T-adapter with Shut-off Valve, 3-way Tee Connector for Handheld Bidet 15/16" and 1/2" IPS, Chrome Finish by Soharic

OK, this works acceptably, but I strongly encourage you to buy a different T-adapter valve. Get the "Luxe Metal T-adapter with Shut-off Valve, 3-way Tee Connector, Chrome Finish, for Luxe Neo Bidets." It is only $2.00 more expensive, and the threaded joining parts are longer on the Luxe. Also, this Bella T-adapter valve is supposed to swivel so that you can screw it on, and then be able turn it to join to your other plumbing. However, as you attach the top of it, the part that swivels tightens up and then it doesn't work. I used this with the Luxe Neo 180 bidet in our second bathroom, and then used the Luxe T-adapter with another Luxe Neo 180 bidet in our master bathroom. The Luxe T-adapter valve is much higher quality. Notice that both of these T-adapter valves have that little bar sticking out - that is for you to adjust your water pressure on the bidet. Straight down is off. Turned fully on, brings it half-way up, becoming perpendicular. And anywhere in between are gradual adjustments. So this valve works, but I recommend that you get the Luxe instead. Also - please use a light-handed approach. Make sure it is lined up correctly, and screw it on by hand. Then only tighten a little with your wrench. If you over-tighten it, it will leak.

I bought this in connection with my smart bidet, which is amazing. This works great, but the only issue is that I had to get an adapter to connect it to the bidet, which required me to run to my local hardware store. I just thought if it was coupled with the product I was buying under “frequently bought together” it would have included an adapter or was already manufactured to fit. Otherwise great product

This was very loose when not installed and even once installed, I had to get the top really tight on the toilet before the bottom of the valve would stop moving. It almost felt like I had to make it too tight. The shut off is very smooth though and although this said it fits most bidets, it didn't fit mine. Mine needed 3/8 but I didn't know that until after I purchased it. I needed to buy an additional adapter but it was the or send it back. It's fine though and not leaking.

My Joy C1 Bidet came with a plastic T-Adapter that I had problems with from the start. I had to buy an O-ring from Ace Hardware and do a lot of tightening before it was leak free. Few months later it came apart and water leaked everywhere.I bought this as a replacement and it has not leaked once since installing it. I highly recommend this adapter as a replacement for the cheap plastic one that comes with the Joy C1 Bidet. The valve is a nice addition and lets me adjust the water pressure to a gentler stream. It also has some rubber seals on the inside to help make a tight seal between the hoses and toilet tank.

This was very simple to install. It also works as described. It's simple to operate. Three positions, the two end positions makes the water come out of one of the two ends. The middle position makes the water come evenly out of both ends. I used teflon tape and it fits perfectly with no leaks. It looks great too.

I would highly advise to get this all metal T valve for your water closet incase you are installing a bidet or a wash. You have the ability to open/close valve that gives you peace of mind in the event of water leaks from any connections. Highly recommended.

Not only did the inlet size not work but one of the outlet sizes didn't match. So it didn't work for my application.

good for what it does. you will need Teflon tape and make sure you don't strip the plastic threads that come out from the toilet

Definitely a must for installment.

The apartment I moved to cheaped out on plumbing (see Accor Technology), so the standard T-fitting that came with my bidet did not fit. This T-adapter is an excellent workaround, no leaks, well made. Very pleased.

Easy to use and setup.

The valve seems great. Finish great the attach nut to the tank good. BUT the threads that the feed hose attaches to are too short. The “nut” on the hose hits the shoulder and so the washer can’t be fully compressed enough. Over tightening sets the plastic nuts up to crack and burst off flooding the bathroom. In one case we added a second washer - but I bet that sets up too few threads engaging and future leaks.

Multiple attempts at using this T-adapter were futile. We repositioned the washer, used less plumbers tape and more plumbers tape. No matter what we did, it leaked. Gave up on it and used the plastic part that came with our new bidet and, voila, no leaks! In short, this was a waste of $12.

This is a solid adapter and is well engineered. The lever turns smoothly and there is no wobble. The threads on the fittings are plenty deep which helps to avoid stripping. The nut that attaches to the bottom of the tank also turns easily without any wobble. And most importantly, no leaking.

I added this just for the first time I look at it and say, "I sure wish I could turn off the bidet water and still have running toilet water."