BTF-LIGHTING3.2FT 1m WS2812B Gold Wire 100leds 100 Pixels Flexible Black PCB Individually Addressable LED Strip Dream Color IP30 Non-Waterproof DC5V for Indoor Lighting

I've bought a couple of sets of these 100 leds/m pixel strips now, combined with BTF's SP105E Bluetooth controller and a 5v 10A power supply from another manufacturer. I've been really impressed with the quality of the led strip and BTF's customer service. While the controller software is quite basic, it does all I need and seems reliable. It picks up the Bluetooth controller and connects quickly every time, and allows control of all the basic functionality very easily. Only thing I wish it would do is save favourite modes, but you could always go old school and write them down! Also wish you could rename the controller Bluetooth name, as I may get a few more for other rooms in the future.In terms of the lights themselves, I can't really fault them. Really nice colours, very bright and super quick to change state. Also as there are so many leds/m, you get very little spotting effect if using to edge light a glass shelf (which is what I'm doing). Even better if you put them behind a diffuser in some sort of profile.Only slight gripe is there's not that many different brightness settings, but I'm not sure if that's a function of the leds or the controller - I suspect the latter again. A nice percentage slider would be welcome rather than steps. Same with the scroll speed of the modes too, not that many different speeds available, when I suspect in reality a much greater range is possible.Overall very happy with the led strips and BTF!

I purchased the 1m 60 LED version of this strip for my PC which has a Dark Base Pro 900 case and Asus Strix X299-E Gaming motherboard. This particular motherboard has a header on the board and comes with a cable for connecting it to WS2812b addressable LED strips, which can then be controlled with the Asus Aura Sync software.After installing the LED strip and connecting it up to the motherboard it works perfectly and is also very bright. The LEDs are individually controlled so you can have, say, a rainbow or gradient effect across all of them etc.One issue I encountered when trying to install the LED strip to my case was that the sticking backing isn't very strong and starts to peel off from the inside of the case within hours of being installed. In the end, I found the best way to attach the strip was to use some sticky fixers (double sided foam pads) which are very sticky, and they have secured the LED strip nicely. Just be aware that you may want to buy some if you intend on using this strip inside your computer!The LED strip has wires and connections at both ends. At one end you have a 3 pin male plug (this fitted into the cable for my motherboard) and the other end has a 3 pin female plug, presumably to chain additional strips together. Both ends also have an extra red and white wire (with exposed ends), which is for attaching to an additional power source. I didn't need these so I cut the exposed tip off and sealed them in shrink wrap although you could use electrical tape or simply cut them off altogether.I also had to remove 3 LEDs for this strip to fit in my case properly. It was simply a case of cutting the strip with a pair of scissors where the white intersection line is marked. The really cool thing about this strip is you can cut the strip up and solder the strips together using 3 wires (+5v, GND and Data) between each strip.

Great Stuff, arrived when they said and the exact item I needed. Thanks

My son used this for his project and was happy

The width of these RGB LED strips is greater than the 10 mm that's given in the listing. Closer to 13 or 14 mm wide. This was quite frustrating because the aluminium channels I purchased did not fit the strips.I was able to cut the width of the LED strips down but it was a real faff to do properly. The width should be correctly stated on the listing.Otherwise, the strips are bright, well made, densely pack the LEDs in thanks to the integrated LED controller, and are easy to use and solder.

got this set up with WLED using esp32. good brightness

Very happy with them, used for a TV backlight project, easy to cut to size and stick down onto TV. Only part which is tricky is they aren't the easiest to fold over for corners but most strips arent!

The media could not be loaded. These lights are very bright and colourful, I stuck them in my pc with the adhesive that comes on the strips and after a day they are still stuck on although I have no idea how long it’ll take till they come loose however they’re very nice recommend them