Snailfly 220 LBS Roof Rack Cross Bars Fit for 2011-2021 Jeep Grand Cherokee Crossbars Cargo Luggage Rack, Aluminum Alloy

1. These are a perfect fit for my 2012 Jeep Grand Cherokee!2. There’s no perceivable noise at 65 mph.3. The installation instructions are a little wonky. They show the end pieces as separate parts but were pre-installed on the crossbars. You have to remove the brackets to place them on the rails. Also, the separate rubber gaskets were not on the parts lost but easy to figure out. I’d say the installation took maybe 45 minutes from opening the package to reading the instructions and dry fitting everything to make sure it all fit together through the actual installation. Tools are included. Also included are an extra screw of each size (2). Since the end piece was preinstalled, I didn’t need the second torx wrench.After my test drive, I tightened everything up which just seemed to be due to the gaskets settling in.In a week or so I’ll be transporting my kayak about 150 miles on the freeway and I’ll update if there are any issues but right now I am extremely happy with this purchase!One quick note: These fit perfectly and look OEM but cost only about 1/4 the price of the Mopar crossbars (I don’t know if there’s a difference in load capacity but these will fit my needs.)

This is really a nice product. Great looking low profile on the vehicle and extremely sturdy. I installed it on my 2021 Jeep Grand Cherokee Ltd. Assembly is fairly easy but the instructions are a bit confusing. The rubber pads for the bottoms of the crossbar "feet" are unnecessary, not addressed in the instructions and almost impossible to utilize - I discarded them. Very happy with this product!The wind noise is definitely noticeable so I will go back and change the location of the bars and install the crossbar feet. Although they are not mentioned in the directions, my assumption is that they may be an add-on item intended to reduce wind noise.

These bars fit the rails that was on the vehicle.They arrived as advertised and assembled quickly and came with tools to assemble them.

They were very straight forward and easy to install (once I removed/loosened the hardware as instructed) The hardware came cross threaded and if you know how frustrating the little allen keys can be you know the frustration haha BUT besides that the low profile looks great as well, compared to the taller options out there and they seem pretty solid!

Directions bad but usable. Rubber boots supplied not covered in instructions so I will have to take it off and put them on after I figured out they needed to be there. I am putting a cargo carrier on it so to keep it from being scratched I will be putting weather stripping on bottom of cargo carrier. The kind used for trucks when you put on a shell.

EASY TO INSTALL, LOOK'S GOOD

I wanted to leave a feedback hoping it helps someone in the future. We bought two sets of these cross bars and installed on two different Jeep Grand Cherokee Trailhawks following the installation method described below. First off, the product came in nicely packaged with one page color instructions and two spare bolts. Second, take that installation instructions and throw it in the garbage. The way I installed it is by loosening all the bolts but keeping everything attached. Right side towers have red R stickers on them and should already come pre-assembled the right way corresponding to Front and Rear orientation. With all the bolts loose lay one bar at a time into the channel making sure you have the same distance in between. Once positioned inside the factory rail, remove top bolts one at a time to apply blue loctite as recommended by other reviewers. This step is optional but helps ensure bolts don’t come loose in the future. With your finger make sure the lip of the tower is seated properly inside the factory rail. Once confirmed, start tighten top bolts alternating until both are tight. Go on the other side and repeat the same steps to tighten the other tower making sure the lip is latched inside the factory rail. Once both towers are secured, tighten small screws under the bar. Repeat all of above steps to install the second cross bar. Remove the orientation stickers and enjoy the finished product.

The crossbars work well on our Jeep Grand Cherokee. They were a bit of a challenge to put on. It is hard to hold the screws in place and get them started with the tool that is provided. So, this took quite a bit of time. One screw came out and luckily, we did not lose it. We carry the tool with us and check the screws every so often to make sure they are tight. They seem sturdy and are a good value for the money.