Speaker Mounts for Logitech Z906 Speakers Wall Mount Tilt & Swivel Adjustable Ceiling Mount for Logetich Z906 Satellite Speaker Mounting Bracket, Single

So I think someone else mentioned that the instructions were not clear, and this is totally true. However when I did figure out how everything was supposed to go, I got it together. I have the Z906s so I had to purchase 5 and they work perfectly. Maybe it was my overthinking at first that they would not hold up well but they did and fit the speakers pretty good. The extension that they come with is pretty useful in case you need that extra reach. In my case I meeded to use that for my center speaker so it could reach put a bit further over the entertainment center I have my tv on. Overall a really great buy once you figure out how to properly put it together

This mount was obviously designed for a different speaker than those that come with a Logitech Z906 system. It comes with an adapter plate because the mounting screw for my speaker is too big to use the speaker mount directly. You have to use an adapter plate that mounts on the speaker. Then the speaker mounting system mounts to the adapter plate. This creates an offset in the geometry. You have to make sure all mounting screws are very tight to overcome the induced offset. It does work even with the offsets.

Let me tell everyone about this mount, at first the instructions were vague, took it a bit to figure it out. I gave up cuz I thought they would not hold my 8 pounder ATMOS speaker’s. They didn’t have any weight limits stated in the listing not anyplace. I set up the return and repacked everything up to return the next day. In the meantime I looked hi and low for a replacement, there just isn’t any with this quality out there. I didn’t want anything that looked cheap. Although I really couldn’t hide the wires, the did come with nice covers to hide the screws. After much search I came across these mounts again this time the listing had bigger speakers? Hum, same product, different speakers?I took a second look at them and found they were exactly what I needed, I was still wondering if the would hold my speakers. I got them up and tested them, Yup, there strong enough, just needed stud to tap into, I found enough for the two front holes, used the back with the anchors, those speakers aren’t going anyplace.I have key hole type speakers, but I can see this working with 1 hole threaded speakers, I don’t want to put any holes in my speakers, I wanted to use what they gave me on the back. Klipsch speaker’s have either key hole or one threaded screw holes for mounting the small surrounds, but ATMOS speakers came the key hole type. I guess they were made to be placed on top of my towers and bounce off the ceiling. I used them this way for over a year until I realized through UTube advance, that configuration was no good. I thought bouncing off the ceiling was how it’s done unless you have them installed in the ceiling. I am not ready for that yet, This will do very nicely for now. In 2 years I plan to upgrade to 7.4.2. That’s a total of 13 channels if pure glory. With this installation I just finished I’m at 7.2.2 and loving it, my new Marantz 7 channel Amp coming soon to take over the load of my Marantz SR7010 AVR. Hope this review helps, happy tunes everyone.I wanted to Give this speaker mounts 3 thumbs up, if you are willing to put time in, be a little creative with mounting and can find a wood stud to tap into, then theses are the mounts for you.As of 10/3/2020 my mounts failed, I put to much weight on them so they didn’t stay up 90 degrees anymore, so I came up with a fix, I tightened them down and attached a wire from the speaker to the bracket with a small screw on the speaker and bracket. I made sure before I tightened and secured the wire the speaker was at 90 degrees angle. The wire kept the speaker upright and I don’t see any further problems with the speaker dropping anytime soon. See photos!

First of all, this is a horrible design. I purchased this for Logitech Z906 speakers. I decided to give it a go since I already had the one delivered to me. Here’s where their design fails. I wanted to use this as a wall mount. Ok, look at the instructions and the very 1st step, yup you guessed it design fail. You’re supposed to attach the pivot head to the wall mount and secure it with the provided screw. Epic fail. The screw head and the wall plate are the same exact size. I have no idea who engineered this but they need to be fired. If the hole on the wall plate was smaller or if the screw head was a little bigger it wouldn’t be a problem. I don’t feel that I should have to go out and buy new screws for something that is brand new. This bracket should have a bit smaller hole with a beveled edge to allow the provided screw to hold everything together and flush.Second, even though they are made out of metal, they’re too expensive for what it is. $22.99 for one wall mount is too much. Not even $22.99 for a pair…. Seriously one wall mount.There are better options on Amazon for speaker wall mounts. Avoid this product.

The mount came completely out of the packaging and was loose inside the shipping envelope. All of the parts appeared to be present. Mount is not adjustable without loosening the assembly screws.

This wall mount kit is really neat. I love the fact that comes with a cover plate to hide the screws to the wall. Over all, is a modern looking, neat wall mount.

Easy to install and mount speakers, but make sure your speaker is the right size for these!

There are fantastic works perfectly