Pro-Grade Black Rubberized Speaker Repair Adhesive Glue (1 oz) - Dries Black

The good quality is superb. I had a whole the size of a nickel in my subwoofer. I created a patch and use the glue. It dried quickly six hours. It wasn’t running. It went all nice and thick and when it was finished drying, it was a smooth finish. Very easy to use bottle and a low quality itself has a strong bond and doesn’t have an odor.

Works well, would recommend getting the smallest option if you dont have to fix alot cause a little goes a long way

This was used to reattach a dust cap on my REL 10"woofer driver from my REL Britannia B3 subwoofer that was having issues. The glue applied easily and filled all required areas well. It cured well in 24 hours. Woofer installed now and running normally 48hr later. Did exactly what I expected it to do. Color in black is exactly perfect for my woofer. I used the adhesive on several tears when removing the dust cap. Was hard to remove the dust cap. But repaired it OK. Had to use more adhesive since dust cap needed it. I needed it because there was extra noise from the woofer due to magnet top plate separation from the basket. I need access to the voice coil under the dust cap to shim it in place when fixing the magnet crack. Dust cap perfect now also. I can highly recommend it and would purchase it again. I was able to clean up a few drips with some nail polish remover easily.

while listening to my daily driver at a low to medium volume, there was suddenly a rattling quite like the voice coil former was tagging the pole piece. had to finish drive home with no tunes in SoCal, bummer. got home and pulled the offending sub box. i found the pulp type cone had ripped off the foam surround about half way around. this is a ddaudio 1508, 500 watt rms, long throw 8 incher, pretty good at hard bass when you have two like i do. i will be getting a recone for this but i wanted to find out if a repair was feasible. i ordered this adhesive (Pro-Grade Black Rubberized Speaker Repair Adhesive Glue (1/2 oz) - Dries Black, Brand: Springfield Speaker ). while i waited for it to arrive, i slit the rest of the surround off of the cone while preserving the overlap, mirroring how the detachment was already. then i cut the dust cover off of the cone to expose the voice coil and pole piece. it is super important to ensure the voice coil travels exactly parallel to the pole piece. so, i stuck 3x5 cards evenly down the gap until the voice coil/cone was stiff to move. folding the surround back i squirted a layer of glue around the cone matching the old surround lines area. a couple minutes later as the first layer soaked in, i went around again with a thicker layer of glue to be sure i had plenty and not worried about tiny amounts of dribble, it's an out of sight sub after all. then, i pulled the cone up slowly to contact the surround plus a little more up, like an 1/8 inch or less, looking for good contact. the next day i went back and added a glue line over the thin lip of the surround and down to the pulp cone as more adhesion, i also added a lip of glue to the back side of the cone and surround, only missing small areas where the steel basket was in the way. a coupe hours later i pulled the 3x5 card shims out, blew out the voice coil with compressed air and glued the dust cover back on. the next day i dropped that sub back in its box and put it back in the daily driver. the first test was some old ying yang twins, me and my brother album. the suspension is already well broken in so i let that sub have it. and for a few minutes i went into over excursion just to see. i went long and hard enough to smell the voice coil adhesive till i backed it off a bit. the glue was holding perfectly and the sub sounded just like its twin that did not come apart. back to banging, and no odd noises, just like it should be. for the next week at nearly two hours a day commute i beat on those subs with gangsta rap/crunk and similar. 2 500watt ddauio 1508 on a jl audio 1200/1. then i went back to my normal metal/hard rock diet. it's been just over two weeks now and the adhesive sold here is still holding like the day i put it on. visual inspection, everything just like i glued it. i still plan to do a recone on this mfg in 2010 sub just because it's so old, but i'm going to wait a while and enjoy the $12 repair, knowing this is a cheap option for the future. good adhesive!

Used this to refill the surround on a 10-in Polk Momo subwoofer. I've been banging away with the bass for about 2 months now and no problems. I'm giving it four stars because I don't know about the longevity. But so far, so good. I'm a Metalhead so I'm not listening to hip hop. But there is still a lot of bass.

Excelente producto

Patched a hole in my speaker with this worked well.

I needed to replace a pair of speaker center cones and this worked very well and has for over the past year with lots of speaker use and no signs of glue degradation.

Worked excellent, dries quickly and holds strong. I bought the 2oz bottle to recone a competition 8" subwoofer. Barely used 1/4 of the bottle and i was generous with application. Friend brought over his 10" and i reglued that for him and i still have well over half a bottle. I can definitely see myself ordering more for more than car audio applications.

The glue worked exactly as the instructions said very simple and will buy again when I need to repair more speakers. I have not seem a downside yet Ron

To reform some speakers

Jai fait 5 speaker et il en reste environ 12 autre haha

Buena adherencia