DEWALT Miter Saw Stand With Wheels, 32-1/2 in. x 60 in Foldable Rollling Stand, Adjustable Height, Durable Steel, 8 ft. Material Support, Universal Mounting Rails (DWX726)

I will say that this stand is not exactly "perfect" for absolutely everything I want it to do, but it's close enough that I would call it the only realistic option for what I was trying to achieve with it. For years I've had a dedicated chop-saw station in my (very small one car garage) shop: saw in the middle, with large work tables projecting from either side, to handle long material. I needed to drastically downsize the footprint of the "shop" duties of the garage space, due to the need to accommodate charging of a newly-acquired electric vehicle. The chop saw situation proved to be the most difficult problem to solve. At first I was somewhat deterred from this stand as an option, I think just due to it being a "job site" stand -- the saw never leaves the garage, so I'm not taking it "onsite" anywhere. But the more I looked at it, the more I realized: yeah, that's probably just about perfect, or close enough. And, alas, it definitely is just what I needed to free-up a TON of space. Now, granted, I am storing the saw on the stand exactly in the way DeWalt tells you not to: standing upright. However, the warnings in the instructions, against doing this, are purely about tipping hazard. And, to be sure, if you stored the saw standing upright, out in free space, it would be disconcertingly wobbly and wouldn't take much to tip it. However, I'm storing it up against two supporting walls. And I made a sort of cleat for the stand arm to rest on. The set-up is absolutely bombproof -- I've pushed on it -- hard -- and it's not going anywhere. So with just a modicum of practical consideration, you can absolutely store the saw standing upright. Do I miss the convenience of being able to walk up and use my chop saw at any given moment, without any set-up or take-down? Yes, a little. But it's not actually nearly as big of a deal as I thought it might be. In fact, there are advantages. By pulling the saw into a more central location (rather than backed-up against a wall), it's a lot easier to clean up after use, and putting the saw away each time encourages me to keep it pristine, rather than just skipping that step. The portability is actually amazing. It's so easy to maneuver into place. Setting it up and taking it down is easy enough. It's very slightly fiddly, and I do worry a tad about long term durability of the lift system, but right now it's fine. What's also unexpectedly great, for me, is the ability to take the saw out of the garage. If I expect to be doing a lot of cutting, I can take it out onto the driveway in order to avoid filling the garage airspace with light dust to settle everywhere. The extension arm feature is fantastic -- it's so nice to have handling of long material built right into the stand, rather than having to go through set-up acrobatics. The one issue I have is that the arms do want to flex down a bit, and the amount of flex depends on how far you have them extended -- which translates in the need to reset the height of the supports. For me this is not a huge problem because my projects tend in the direction of doing a bunch of similar cuts all at once -- rarely do I have the need to be switching back and forth. I have to saw that assembly was a bit fiddly and frustrating. There are certain aspects of the design that I think could use some low-key debugging. If they ever release a Mark II version, and fix a handful of minor annoyances, I'd consider it. It's a great stand and will be my solution until they invent a full sized chop saw station that materializes out of thin air when I need it, then disappears when I'm done :-)

What a great ease of use and quality item. I set up my dealt 20v battery on to this after doing some board and batten panels around my house. It was very easy with this table and my miter saw. Great value also. The height and portability is exactly as it was described. Great for DIY'ers!

I rarely leave reviews, but for the DeWalt Miter Saw Stand (I have the rolling heavy-duty model), I absolutely have to. Simply put, this is the Cadillac of jobsite equipment. If you are doing any kind of serious trim work, framing, or deck building, this stand is not an optional accessory—it's essential for your health and efficiency. The Back-Saving Difference My biggest motivator for buying this was honestly to save my back. Wrestling a heavy 12-inch sliding miter saw (even with two people sometimes) onto sawhorses or a fixed table is a recipe for a bad day. The genius of the DeWalt system is the pneumatic assist lift. When it’s time to set up, you simply flip the lock, grab the handles, and the saw raises itself into working position with incredible ease. When you’re done, the dampened lowering mechanism means you don't fight gravity; it glides the whole setup back down for easy rolling and storage. It truly eliminates the strain of hoisting and lowering. This feature alone makes it one of my single favorite pieces of equipment I own. Built Like a Tank, Smooth Like a Caddy Beyond the lift mechanism, the build quality is exactly what you'd expect from DeWalt. It's solid, the locking mechanism for the saw brackets is foolproof, and the support arms glide out and lock firmly without any slop. The large wheels handle rough terrain (gravel, lumber scraps, uneven concrete) on a jobsite with no problem. When folded up, it takes up a surprisingly small footprint, yet when deployed, it offers exceptional stability, even when cutting long, heavy stock. If you are on the fence due to the price, stop thinking and buy it. The cost is negligible compared to the lost productivity and pain of a thrown-out back. This stand will pay for itself in hours saved and physical discomfort avoided. Five out of five stars—a must-have tool.

Like every woodworker I know, my shop space is limited. EVERYTHING must be portable and/or on wheels. My wife has the twisted perception that her car should sleep in the garage at night. Women! Actually, it has become a blessing in disguise. When I put everything away and in it's place so that she can park in her half of the garage, it forces me to be neat and tidy.....................and creative, utilizing every cubic inch. My DeWalt Miter saw is not a tool which I use every day.....................but I would like to use it more than I do. It was always such a pain to hoist it on top of my outfeed table and cut the various pieces to length. Yes a cross-cut sled works well when the stock is two to three feet in length. Pieces longer than that are just too cumbersome..................and dangerous to try and cut to length on the table saw. Table saw kick backs are scary so when I process my raw lumber, which is usually purchased in 10' lengths, I go to the miter saw, and since my limited shop space doesn't allow for a dedicated miter saw set-up, I have always struggled with set-up, hobbling together a jury-rigged cutting station. I knows that "purist" woodworkers sometimes feel that the miter saw is a construction site tool and simply is not precise enough for fine woodworking. Personally, I don't know what planet they are living on. Most modern miter saws have such sturdy and elaborate adjustment mechanisms that they are capable of incredibly precise...................and repeatable cuts. Now..................as to my review of this miter saw stand. Packaging is wonderful..................and the stand itself is built like a tank. The assembly is fairly intuitive which is good since the printed instructions are horrible. Once assembled, which requires about 15 - 20 minutes, I placed my miter saw on top and attached it as instructed. The hoisting and lowering mechanism is smooth................and really effortless with the gas assisted piston. When collapsed, my miter saw stores neatly against the wall yet sets up rapidly when needed. Bottom line? This is NOT a substitute for a dedicated miter saw station. There is no extended fence. Because there is no extended fence, there is no adjustable stop against which the work piece can be registered for repeatable cuts. But I didn't expect any of these and it's NOT what I purchased this stand for. I bought this to solve a portability problem which it does marvelously. It is amazingly rugged, gracefully balanced and portable as can be. It is probably better suited for the construction site than a furniture shop, but all of us must improvise. This tool does exactly what I wanted it to and with a little ingenuity, I have designed and built an extended fence system for repeatable cuts. Overall, I love this thing. VERY well built and exceptionally engineered. Lastly, it is so adjustable that almost ANY brand of miter saw will attach easily. I would definitely make the same purchase again.

Yes, this is a sturdy, heavy saw stand which ought to fit a wide variety of saws. It works fine for my 30 year-old Hitachi slide saw. I think that others have described this saw stand fairly well, but there are still a bunch of issues that I've come across not mentioned in other reviews, particularly in terms of configuration. First off, the product description completely fails to describe the actual dimensions of the stand with the supports fully extended. The answer is 8' on the nose, so you can indeed trim the end of 8' material and still be balanced, depending on how you locate the saw on the stand. It's important to understand that the stand is asymmetric front-to-back (as seen when you face it to make a cut). This means that it matters which way around you install your saw, i.e. whether you have the wheels to your left or your right. If you want to have the greatest possible amount of reach for the supports, then you'll want to have the wheels on your right. This is because the mounting channel for the supports is not set in the centre of the stand, but the bars at the end of the supports are symmetric. This is shown in my pics. Having the wheels on the right was not a problem for me because of other factors noted below, but at may be for you. It's worth thinking twice before you put everything together, since it's a hassle to unbolt the saw and turn it around. Before you put things together, you may want to think about whether you're left or right handed, whether you like the infeed or outfeed to have more support, and where you have the centre of gravity of the whole assembly. You may or may not want to mount the saw centrally left-to-right on the stand. I didn't want to for a couple of reasons: a) I wanted to have the maximum available support length on the left. This is because I like the infeed on the left, and even though I'm left-handed I operate the saw with my right hand, and want to hold the material I'm cutting mostly with my left. In my case, I was able to set up the saw pushed over to the right enough to give me about 52" of available infeed support on the left. This resulted in a matching reduction in the available maximum length of support on the right. b) I wanted to have the lowest possible centre of gravity when the stand is folded up and standing upright. This makes it easier to move around on its wheels and less likely to fall over when not resting on all fours. If you want to get maximum support out of the in/outfeed supports (to cut the widest possible stock), then you'll probably want to mount the saw as far back as possible on the stand. This is all a result of the design asymmetry mentioned above. For me, this was not a problem, and didn't result in an unacceptable weight distribution, but I imagine that for some saws this might be a problem, especially if its design is particularly back-heavy. Finally, a few criticisms: The product I received had a mis-adjusted release catch, which meant that it would not lift up at all until I fixed it. This is lousy quality control. Yes, anyone getting a stand like this ought to be able to figure out how to adjust it, but they shouldn't have to. I was surprised by how much force was required to raise the stand up. I don't think that my saw is particularly heavy, and the docs keep warning about how it might spring up on you if you're not careful, but I sure don't feel that's a problem for me. A minor note on standing the saw/stand upright. The docs tell you not to do this, but of course, we all will, and they've obviously designed it to be able to do so. Given this, it's annoying that the hoop that the stand rests on in its upright position has no anti-scuff rubber on it. It's a little thing, but you get your nice new stand in official brand-yellow paint, and the tail end is going to get all scratched up on the first day. I should also note that the stand I received was missing the length stop and its associated knob. I was able to get this supplied from DeWalt customer support, but a) Any missing component smacks of poor quality control somewhere in their manufacturing/packaging. b) The missing part took two weeks to arrive. c) It was a pain to deal with the DeWalt customer support web site. In particular, I had to file my claim with the exact missing part number, but this was not shown in the docs supplied with the saw. Finding the part number was non-trivial because I had to find the right exploded parts diagram, for exactly the right version of the stand, and it appears that they've gone through multiple versions. All told, getting the missing parts took a ridiculous amount of time - a big pain that I shouldn't have had to endure for what ought to be thought of as a high-end brand-name product.

I won't go cover the same ground as other reviewers suffice to say that its a good piece of kit and deserves every star that I've given it. What I would like to cover in my review is the things that other reviewers haven't covered: - its BIG! I stand 6' tall and this reaches my chin when its stood upright. - Its heavy (read well constructed). Which explains why it cost an arm and a foot in shipping costs - the basic unit comes in one piece with assembly required for the lower legs, riser handle and material support rollers - looking at it, it looks a bit flimsy around the wheels. Don't believe your eyes! It's constructed in such a way that there isn't a flimsy piece in it - when closed down, there is a locking bolt that prevents the mechanism from opening while vertical - the material supports use an unusual split tube mechanism to control vertical movement. Not sure how I feel about this - although a universal mounting, the hole spacing on my saw meant that I couldn't mount it dead centre in the tray. - there is a clearly defined front and back. The front has the logo (of course) and the back has a cord minder - when sliding the the material support roller arms on, there is a detent which prevents over extension or removal - comes with a handy onboard hex key. I was unable to find the spanner mentioned in the assembly instructions Just a few things I'd like to mention/expand on: My inability to mount my saw dead centre on the tray is a minor thing. I intend at some point to make an adapter plate which should resolve this. I don't have a De Walt saw but I'm sure if I did, that it would fit perfectly. Further, this trolley/workstation is of such a size that it should cater to even the largest compound mitre saw. one of the material support rollers isn't parallel to the floor. Not sure what to make of this yet but I don't consider it majorly alarming. I chose the De Walt over the Porter Cable version partly because it was minorly cheaper but mainly because the Porter Cable had a number of reviewers complaining about the lifting mechanism locking up. Strange as the PC version appears to be exactly the same design as the De Walt. Before purchasing this, I had considered building my own out of wood. Ultimately I decided not to due to uncertainty about stability. The price of the De Walt was competitive but I really got killed on shipping costs. I'm presently getting together items for constructing my own own router table so will probably revisit the idea for for that project. Given that the router installation will be much lighter and not be under such heavy weight stress, the idea is probably much more practical. Finally, some background info. The concept of a rolling stand is pitched at job site portability. In my case (being a hobby woodworker based in my garage), I felt that my compound mitre saw was a tool that I would use infrequently hence I wanted a scenario where I could readily access it but pack it out of the way when I didn't need it. Now that I've had a bit of experience with this form of portable workstation, I'm keen on doing the the same for my router table (as mentioned) and also (at some point in the future) my table saw upgrade. As an amateur woodworker, I operate out of my garage and that is a space that is rapidly decreasing in size. The idea of easily moved, easily setup workstations has a great deal of appeal. Addendum: All my previous comments stand however my perception of this unit has changed slightly in light of recent discoveries. Let me explain: As mentioned I am planning to upgrade my table saw at some point in the future. I've had my eye on a De Walt DWE7491 for some time but have recently discovered the Metabo version (sorry don't know the model number). The De Walt has a matching stand much like the Rolling Mitre Saw Stand (sold as a separate unit) whereas the Metabo has wheels and four built in legs which unfold from the unit itself. I'm becoming very taken with the Metabo... its compact, centre of gravity is low (basically on the floor) but its still portable. In light of this, I'm beginning to see the Rolling Mitre Saw Stand as using a sledge hammer to crack a nut. As far as I'm aware, no-one makes anything similar to the Metabo concept for Mitre saws so buying one is out of the question. However as an amateur woodworker, making one is quite achievable. Having said all of that, this takes away nothing from this unit. In my opinion, it remains an excellent choice for job site portability and certainly the best one that is commercially available.

This stand is probably the single best mitre stand out there. Collapsible and portable, I am now able to take my mitre saw to any job site without having to lug the saw by itself and then find a place to put it. I am able to work at ground level, full height, and even a bit lower than full height. It is solidly constructed and the release mechanism is also quite solid. My only complaint is with the length of the release cable, it took me a bit of testing to get the release to activate but was easily overcome, just needed to move the release lever a bit further (it got tight so I presumed that was the stopping point). It moves up and down quite well with it being pneumatically operated. Highly recommended.

This stand is a total powerhouse—sturdy, durable, and super easy to move around thanks to the smooth-rolling wheels. It makes storing my miter saw a breeze since it takes up way less space than a bulky workbench, and I can easily wheel it out whenever I need to work. Being able to roll my saw wherever I need it—whether in the garage, on the job site, or even outdoors—is a total game-changer. The adjustable height ensures every cut is comfortable and precise, and the build quality is classic DEWALT—built to last and withstand heavy use. If you want a reliable, space-saving, and portable miter saw stand, this is the one. Highly recommend for pros and DIYers alike! 🔧🛠️🚀

Excelente precio atencion y producto principalmente.Excelente precio atencion y producto principalmente.Excelente precio atencion y producto principalmente.Excelente precio atencion y producto principalmente.

Bon produit

I bought it for my Ridgid miter saw and it mounted on the stand great. You will want to remove the mounting bolts (that secure the saw to the stand) first and then loosen the bolts for the adjustment rails that the saw will sit on and bolt too. Measure the distance of the mounting holes on the saw so you can adjust the mounting rails and holes so they will be roughly where you want them when you lift your saw onto the stand. Then bolt your saw to the rails and snug up the bolts but not tighten so you can move the saw to where you want it to sit on stand. Once you even up the position of the saw on the stand (front to back and side to side), then tighten all of the bolts up. I found it very easy to mount the saw to the stand and I'm pleased with how well it fit and was secured. Heavy duty stand, I highly recommend it.

Heavy duty, and compact. Would recommend if you have a chop saw, will hold long material without falling. Life saver and must have!

This stand was very easy to assemble and attach my saw to. Additionally, it was a great price compared to stores in my area. Only had a slight issue after it was assembled. It would not lower back down. Watched a couple YouTube videos and fine adjusted the lever spring mechanism. Works very well now. From reading other reviews, it appears that this is a fairly common issue.