Question 1

Could i use this device to determine if there are 5g towers in my town? distinguishing between 3/4/5g? it's for a research project.

Accepted Answer

In my opinion the tinySA would not be helpful for studying 3G, 4G or 5G cellular networks. The upper frequency limit for measurement with my tinySA is 960 MHz.  Approximate frequencies for cellular service are as follows:
1G operated at a frequency of around 850 MHz and 1900 MHz.
2G and 3G networks operate at additional frequency bands and spectrum around 2100 MHz.
4G LTE operates at additional frequency bands around 600 MHz, 700 MHz, 1.7/2.1 GHz, 2.3 GHz, and 2.5 GHz.
5G operates on two bands FR1 is 450 MHz-7.125 GHz and FR2 is 24.25 GHz & 52.6 GHz.
Most cellular frequencies far exceed the upper frequency limit for the tinySA and cannot be observed using it. Where signals are observed below 960 MHz, its likely that 3G, 4G, and 5G signals and probably other services will share spectrum. One probably cannot get enough info to know which signals are of a certain generation – 4G vs 5G vs 3G.

Question 2

Anyone compare the readings on this spectrum analyzer to a different spectrum analyzer to see if the readings are accurate?

Accepted Answer

There are quite accurate.

Question 3

Can this be used to analyze TV antenna signals and help to aim it?  Connect directly to the 75 ohm antenna wire?

Accepted Answer

It is possible to use the TinySA to measure the signal level of a TV channel while positioning an antenna, but it isn’t easy to do so and it requires a good understanding of some mechanical and more complex electronics issues. 
Two of the simpler issues one may have to deal with are: 
1.	You may not be able to see the screen display well enough if you use this instrument outdoors or other bright lighted areas.
2.	 Attaching a coaxial cable like RG-59 or RG-6, typically used with TV antennas, to the TinySA is problematic. A between-series adapter is usually required (a type “F” female input to type “SMA” male output being typical). The torque imposed by holding and moving the TinySA with the adapter and coax attached can damage the TinySA – especially its SMA connector. 
I do not recommend the TinySA for most people. It is a great little instrument for little cost, but it’s not meant for the inexperienced or non-technically minded. Check out the TinySA website and read the Wiki or download and read the manual. Technical information about the TV signal(s) you want to measure must be found elsewhere. If you are not overwhelmed by all the information, then the TinySA may be just what you are looking for.

Question 4

Has anyone used this to measure the harmonics generated by an analog synthesizer's oscillator? 100kHz lower threshold still seems high.

Accepted Answer

You need an audio spectrum analyzer. I don't think this would work for you.

ASIN	B08H1S2SYR
Brand	AURSINC
Brand Name	AURSINC
Compatible Devices	Windows & Linux PCs
Compatible devices	Windows & Linux PCs
Customer Reviews	4.5 out of 5 stars 398 Reviews
Item Dimensions	16.5 x 10.2 x 4 centimeters
Item dimensions L x W x H	16.5 x 10.2 x 4 centimeters
Manufacturer	AURSINC
Model	TinySA Spectrum Analyzer
Part Number	Tinysa Spetrum Analyzer
Power Source	Battery Powered
Power source	Battery Powered
UPC	753318593381
Unit Count	1 Count
Unit count	1 Count

AURSINC Hand Held Spectrum Analyzer, tinySA MF/HF/VHF UHF Input for 0.1MHZ-350MHz, UHF Input for 240MHz-960MHz, Signal Generator with 2.8 inch Touch Screen Battery

Details

Details

Description

Specifications

Reviews

Common Questions