Zigbee Presence Sensor FP1E with Matter, REQUIRES Aqara Zigbee 3.0 HUB, mmWave Radar Wired Motion Sensor, AI Spatial Learning, Supports HomeKit, Alexa, Google Home, SmartThings

Wanted something a little less than an fp2 and a little more than a P1 PERFECT BALANCE Easy to set up and works flawlessly I love Aqara products

Reports of it disconnecting: Fix using Hubitat is to install the Aqara P1 motion sensor, from package manager, manually Zigbee pair nearby hub (within 1 m) with avoiding repeaters (C8), directly after doing a rebuild Zigbee network TWICE which allows a better pairing operation , also after the first pairing , save then do a re-pairing operation again, the same device will be found and further data about the sensor will have been added, the device will have been recognised and the driver loaded. If the attributes like occupancy /motion show and shows ONLINE for longer than a few minutes, then you have probably succeeded in pairing fully to Hubitat, if not re-do the process above as it may take a couple of attempts depending on the interference from surrounding equipment. I now have 3 of them and found them very good for medium sized rooms lounge/kitchen/dining etc to keep lights on when occupied. I also dabbled with HomeAssistant and put it on a raspi-pi and used a Sonoff USB dongle plus with co-ordinator software installed, if it has been set to a router, it can be easily flashed back to co-ordinator-search for sonoff website and online flasher (which is what i had to do) Everything I have tried on HA just pairs instantly, and in the process of moving some of my problematic Zigbee devices to it. Works as expected with ''their'' hub and usually needs updating from 0026>0029 which cant be done with other platforms that i know of 'yet'

Works that's really all I can say mine is connected to home assistant through mqtt

Best milliwave sensors for smart home projects as long as your in the room what ever you have paired with this device rather through its native hub and app or through home asistant

I decided to purchase the Aqara FP1 Presence Sensor to address a common issue in my home: lights being left on unnecessarily and ensuring lights turn on when someone enters a room with low natural light. I use a Philips Hue motion sensor to measure light levels, which complements the FP1 perfectly. Installation and Setup The installation process was straightforward and hassle-free. Pairing the FP1 with Home Assistant was a breeze, and I had it up and running in no time. The instructions were clear, and the magnetic base made it easy to place the sensor in the optimal position. Integration and Performance The integration with my existing smart home setup has been seamless. The FP1 works flawlessly with Home Assistant, and since I started using it, my lights come on and go off exactly as needed. This has significantly improved the efficiency of my home automation, ensuring that lights are only on when necessary. Key Features High Sensitivity: The FP1’s ability to detect even minor movements, such as breathing, ensures that it accurately detects presence, even when someone is stationary. Flexible Placement: The magnetic base allows for easy and flexible placement, ensuring optimal coverage. Reliable Automation: The sensor’s precise detection capabilities have made my home automation more reliable, reducing energy waste and enhancing convenience. Overall Experience Overall, I am very satisfied with the Aqara FP1 Presence Sensor. It has addressed my needs effectively, and the integration with my smart home system has been smooth. The sensor’s performance has been reliable, and it has made a noticeable difference in how my home automation functions. I would definitely recommend the Aqara FP1 to anyone looking to enhance their smart home setup with precise and reliable presence detection.

Much simpler to use than the FP2 but also lacks the extras such as the light meter and the ability to set zones. We have ours set up in the utility room where we just want lights turned on. Works really quickly if paired with an Aqara light switch.

When they work they’re great. However I’ve bought two and both kept disconnecting and had to be reset. I’ve returned both of them now

Bought two of these, one for the living room, one for the bedroom which should mean that for the majority of time, as someone will be at home, presence would be detected. Had hoped to set up an automation to turn on the security system when no one is detected at home for 20 mins, in case the last person to leave forgets to. Had also hoped to set up automations to turn on and off devices if going to bed (turning on lights if walking around at night etc) But in the end, I wasn't able to do any of that as the sensors report absence when only a couple of meters away from them. Tried adjusting sensor distance. Raising the sensors off the floor, using AI learning when rooms are. None of it helped. They detect me with perfect line of sight for a couple of metres, but the moment I sit down or walk behind the sofa it claims there's no presence. It's as if they're line of sight as the moment I stand up the app shows I'm only 2 meters from the sensor. The whole reason I went with these instead of cheaper motion sensors was the present detection rather that motion checking by line of sight. In the end these sensors just became paper weights.

Funciona muy bien y se enlaza a la primera.

Vorweg: Ich hatte längere Zeit TuYa Radarsensoren die das ganze Z2M-System mit Statusmeldungen zugespammt haben. Neben dem Problem funktionierten diese TuYa Melder auch nicht immer zuverlässig und haben oft Fehlauslösungen gehabt. Nun habe ich diese beiden Melder rausgeschmissen und gegen diese Aqara FP1E getauscht. In der Decke habe ich mir dann ein USB Kabelnetzteil von Logilink reingesetzt damit der FP1E auch dort Strom bekommt. Da der alte TuYa Melder so groß war, wie eine GU10 Lampenfassung habe ich mir eine adaptiert und den Aqara dort eingebaut, siehe Foto. Passt so grade ebend. Lediglich die Halterung musste ich dafür anpassen, da das Gelenk hinten nur Magnetisch auf eine Metallplatte mit zwei Schraublöchern geht. Der Sensor ist dafür ja aber auch nicht gemacht, sondern für einen direkten Anbau an die Decke. Aufgrund des Lochs bei mir und der doch recht großen Aufbauphase entschied ich mich für den etwas improvisierten Einbau. In Zigbee2MQTT konnte ich es nahtlos ohne Gebastel einbinden (Zigbee2MQTT 2.0, HA 2025.1, Skyconnect Stick, ca. 150 Zigbee Geräte). Ich wunderte mich erst, dass der Sensor ständig Präsenz anzeigt, aber dafür muss einmalig das "AI Learning" in den Einstellungen aktiviert werden , damit der Melder sich kalibriert. Das würde aber in der richtigen App von Aqara sowieso gemacht werden müssen. Der Melder arbeitet wirklich hervorragend. Auch die Auslösedistanz funktioniert relativ genau. Damit kann ich unterbinden, dass der Vierbeiner das Licht auslöst, das konnten die TuYas nicht so präzise. Auch das Routing des Netzwerks über die Aqaras funktioniert laut Map sehr gut. Dank Zigbee ist die Latenz des Aqara unfassbar gering, dass es nicht auffällt ob es ein hart geschaltetes Licht mit Analog-BWM ist, oder der Aqara. Einziger Wehrmutstropfen: Der Melder hat KEINEN Sensor für die aktuelle Beleuchtungsstärke. Somit fällt eine Abhängigkeit der Schaltung nach Helligkeit leider raus. Dank Home Assistant und der Sonnenstandintegration kein Problem, wäre aber trotzdem schöner gewesen mit einem Helligkeitssensor. Dafür hat der Aqara FP1E seltsamerweise aber ein Temperatursensor Onboard, den ich nicht benötige. Fazit: Begeistert! Preis/Leistung wirklich Top. Bis jetzt keinerlei Fehlauslösungen, schnelles präzises Auslösen und einfache Installation Dank USB. Kann ich nur empfehlen das Teil.

J'ai acheté ce capteur de présence pour allumer et éteindre la lumière quand j'étais dans le bureau ou dans le salon. Il fait très bien son travail il est reconnu sur Home assistant sans aucun problème le seul petit bémol c'est le câble USB qui doit être branché mais à part ça il fonctionne très bien.

HA＋z2mで運用しています。先日のアプデでAI空間認識含めフルサポートされました。 GOOD ・検出/クリアが早く正確 ・ゴースト検出がない ・(感度:高で)静止してもクリアされない ・検出距離がZY-M100等に比べ正確 BAD ・直付ケーブルのため長さ調節が面倒 ・価格がやや高い ・検出距離の更新が高速なため、ちょこまか動く場合にzigbee通信を圧迫しないか心配 上記BADに目を瞑れば、zigbeeミリ波センサーとしては完成形と言えるレベルだと思います。

Super czujnik działa rewelacyjnie