ULBTER Top+Screen Protector for Nikon Z6 III Z6III Camera [2+2Pack]

This screen protector fits my Nikon Z6II/Z7II perfectly. Installation was easy — no bubbles and aligned just right. The clarity is great; it doesn’t affect the LCD view at all, and the touch response stays smooth. It feels durable and adds peace of mind knowing the screen is protected from scratches. Solid quality and exactly what I needed.

Was a bit hesitant to opt for this product versus a slightly higher rated competing product, despite the lack of top screen protectors in the competitor’s offering. But overall, this turned out to be a fine choice! The advertised contents were all present and none of the glass protectors were damaged. The entire kit arrives in a sealed plastic “box” about the size of a cassette tape case (remember cassettes?). Years of smartphone screen protector installation have trained me to hate the process of glass protector application. I loath it. The meticulous line-up and attempts to not capture dust underneath the protector drives me nuts. However, this was WAY better of an experience than typical due to the smaller size of the protector in this use-case. It still requires some patience and care, but I managed to get a perfect application on the first attempt. I did not use the included application stickers, though, to aid in installation. The likely would have been fine, but I instead used scotch tape. I affixed a strip of tape to each of the short edges (back protector) on the top side of the glass. I then had a helper pull off the back-side film while I was holding the scotch tape and then I used the tape to navigate the protector into exactly the right spot against the camera screen. Gently set the protector onto the rear screen, checking the alignment once more. Then once I knew it was positioned well, I did a single finger swipe along the middle of the protector, horizontally, and it adhered with zero bubbling. The top protector, while much smaller than the rear, was actually slightly more difficult to position, just due to the more limited viewpoint given finger size. But ultimately it adhered quickly and perfectly with no bubbles. I used a single piece of scotch tape on the top-side of the glass to use for alignment. The only con (though I would consider it a nitpick) is that I am not entirely convinced the rear screen protector is as optically transparent as stated. It seems like it might be ever so slightly “cloudy” and reduces overall contrast a tad. But honestly, I use the EVF for composition and focusing 99% of the time and only use the rear screen at times while chimping, so it’s not a huge issue for me. Again, happy with this overall and appreciate the piece of mind it brings in protecting my camera body.

Perfect fit for nikon z6iii. Simple install. Clear glass. Not sure hat the top glass is a bit thicker. And since it is flat with body it looks like a square glass bump. Nothing too deep, and great fit with clear view.

Fit my Nikon Z6ii perfectly, went on with 0 bubbles, barely even notice it's there.

The glass was easy to install overall. I recommend leaving a tiny gap around the edges instead of trying to align it perfectly flush with the bezel. The hardest part is getting it perfectly centered. Despite taking my time, I still couldn't avoid getting a tiny dust particle underneath. The oleophobic coating is disappointing. It picks up fingerprints almost instantly, so the screen needs frequent wiping. The main rear screen still folds and closes normally with the protector installed. The top LCD protector sits noticeably proud of the camera body. I'm a bit concerned that it could be easier to catch on something and eventually peel off. I'm also not convinced a screen protector is really necessary on a camera. My Canon 70D went through 12 years of use with no protector - only the plastic around the screen became worn and the display picked up a few light scratches, nothing that affected usability. I decided to try one on my new Nikon Z6 III for extra peace of mind, but I'm still undecided whether the trade-offs are worth it.

Great product. Fit great on my camera.

Great fit on my Nikon Z6ii, successfully installed the touch screen and upper monitor glass without a problem! No bubbles, touch screen sensitivity was not affected. Clarity is great, almost invisible apart from the edges being raised. Great quality and great value for the money.

Purchased this one as an economical solution and to replace a brand that I like when it comes to filters and lenses. I really like the packaging and the amount of suppliies that are provided with the screens. They were easy to apply, fewer air bubbles (which is a constant problem with these things) and seems to be substantial enough to take the wear that the device will have to endure. I am still skeptical about the hardness and the ability to resist scratches but time will tell. Worth the investment even if it is short lived.

Application is easy if you have experience installing tempered glass protectors to phones. It is better to wash hand before doing it. The description is miss leading as this is a 2 pact and not 3. But that is fine for the price. Wet wipe is dry but (again, for the low price) that is ok because nowadays everyone have 70% alcohol around and can easily make it wet again.

Sitter fortfarande på

Arrived on time and as described. Simple to install.

Parasını hakeden ürün,2 adet gelmekte, sorunsuz uyguladım.

About the first time I’ve had an excellent result fitting a screen protector. I often run without one as they invariably end up with dust or bubbles. Not so in this case, the kit is comprehensive with wet and dry wipes to clean the screen, plus a very helpful sticker to pick up rogue dust spots that may drop before fitting. I can’t vouch for the level of protection and I hope I don’t find out! My only criticism is regarding the top screen protector as it doesn’t sit flush as previously pointed out, perhaps a slight bevel would help, but I’m nitpicking. Recommended.