CB09 CB09U Graphtec Blade Holder with 15pcs Vinyl Cutter Plotter Cutting Blades 30/45/ 60 Degree

Exactly as expected. Works with my plotter perfectly. Easy to install once you get the blades in. Blades do take a little practice or perhaps my fingers are a bit clumsy. Overall very pleased, would purchase again.

I had to make ZERO modifications to this Blade Holder, it fits SNUGLY (but it fits) into the Blue Pen Adapter that comes w/the Cameo 5(IYKYK) and I also purchased the Cameo 4 set of adapters (black gray blue and white) and I only tried the blue one and it fit tightly as well. The way you load the blade into this housing is a little different. Yes you unscrew the black end buttttt it doesn’t hold into the housing like the EVISWIY one (although they both look identical) you load the blade with the spring over it into the end cap you took off, then align the silver part of the housing and you’ll feel the spring and it’ll push the blade out as you screw it on. Twist the blade at the top to retract and extend the blade as normal. I can make die-cut and kiss-cut stickers with this by changing the FORCE on Silhouette Studios. Idk if the blades are the same as EVISWIY but these seem to not drag, it performs clean cuts every time!

Amazing! I am so glad I found this! These blades last a lot longer and cut soooo much better than the blades specifically made for my cameo 4. Definitely a must for small and/or intricate designs as well as every day cutting projects! You just have to YouTube tutorials on how to set the depth properly, basically, you barely want to blade sticking out.

Works great for graphtech

Been using a Craft Robo Pro (CE5000-40) since 2010 or so. I've always used a brand called "Clean Cut", but they're pretty expensive. Some years later, I found that amazon blades were actually pretty decent. Firstly, I think clean cut will last a lot longer, however, the amount of blades you get in this set seals the deal. I'd expect a clean cut to last 6 months while one of these blades lasts at least 1-2 months, possibly more, I haven't worn them down yet ;) Here's some important info! The holder that's being sold with these blades is a big NO-NO!!! Oh my gosh is it a bad holder! Don't use it!!! Reason being, it's "too low". Your plotter has a "tool-up" and "tool-down" position. DOWN when it cuts and UP when it lifts off and moves to the next area to cut. Since the holder being sold here is "too low", it will allow the blade to scratch the surface of your material as it moves from area to area. I highly suggest using the original blade holder that came with your plotter, and yes, these blades will work with it. If you use your original blade holder, DO NOT USE THE SPRINGS THAT CAME IN THIS KIT! They are too short. You must use the old spring that came with your older blade, they're much longer and required for the blades to work in the original holder. 4/5 review, -1 because of the holder, but +4 because these blades are a super value and make very precise and clean cuts! I would highly suggest that the seller stop including the holder and only sell the blades, and please, include the LONG springs that work with the original holders!

Awesome for my cameo3. It blows the autoclave away. I was cutting really detailed designs (grateful dead stealies and bears) and the stock blade was lifting the vinyl pretty bad. This blade made the nicest most perfect cuts ive ever seen from this machine. Setup was really easy, just assemble and test by hand on scrap. Put it in the machine and run a test cut to verify and you're done unless you want to adjust further, in that case just repeat the same process.

These work just as well as expensive ones, however note that mine came color mismatched from the images on the listing. So I would visually double check them before using. The 45 degree ones were the correct color, but the other two were swapped. I was so confused why the ones I thought were 60 degree ones were not cutting through thicker material, but it was because they were actually 30 degree ones. Besides that mix-up, the blades work great and actually last quite long even though I make stickers almost every day.

First time I've ordered off-brand blades for my vinyl cutter and I've been pleased with what I've used, so far - they were easy to install and are very sharp. They cut cleanly and quickly. The colored tips aren't the same as the blades I had before, so I simply labeled the box with the correct blade angle for each color.