3-3/8" (85mm)-30T, Metal Working Circular Saw Blade, Arbor 15mm with 3/8“(10mm) Wahser, Use on All Brand 15mm Arbor Cordless Saw, Metal, Steel Iron Bar, Sheet, Angle Cutting

Buen corte,en las tuberias de emt

The LSHUZIYU 3-3/8" (85mm)-30T, Metal Working Circular Saw Blade is advertised "Use on All Brand", but as two of my pictures show, the outside diameter of the blade exceeds the capabilities of my saw. When I noticed the problem I measured the diameter of the blades that came with my saw (3"). Then I measured the distance from the center of the spindle to the furthest point inside the blade cover and found I needed a blade no larger than 83mm/ 3.25" (almost an eighth of an inch smaller in diameter than what I received, 85mm/ 3.35"). I didn't see the blade diameter specification in the saw's box when I ordered the blade (I eventually located that information on a side-panel). So, shame on me for thinking "small" circular blades are of a "universal" dimension (except for the center hole, of course) when I read "Use on All Brand" in the advertisement. I really did "assume".....However, I *WILL* commend the company on it's EXCELLENT packaging. It's easy to open - but almost impossible for that to happen accidentally. It also protects the product from damage in normal - and maybe even more abusive than normal - shipping. Once the box is opened there are three tabs that hold the blade in place, used to prevent the blade from sliding around inside the box. After bending the cardboard tabs out of the way, then I could lift the bag which contained the blade and the sizing spacer-washer ("wahser" as used in the informational paragraphs describing the blade) which is used to accommodate various motor spindle diameters (which too aren't "universal", apparently because my saw uses 7/16ths of an inch, not 5/8" or 3/8" - the sizes of the spacer-washer). The edges of the blade are further protected with a vinyl sleeve that once removed, exposes the blade's "teeth" - which are VERY sharp.This product appears to be made with attention to detail, seems to be of high quality and packaged well. I am disappointed it didn't fit my saw, and disappointed again, that I couldn't present its use in a video.

Bought it to cut tin for my pole barn. Used it in my Ryobi plunge saw. Cut the tin with ease .

This blade came in a box to protect it from getting bent. That was very nice and sharp worked beautifully.

Great back up blade. Worked like a charm while using my my compact circular saw to rip down pallets. Seems like a quality build.

This item is small. Yes, the description says "3 3/8", which is accurate, but I guess I didn't realize just how small that would be: it's about the size of the palm of my hand (I'm about 5'8" and my hands are neither huge nor tiny). It actually fits fine on my cordless Ryobi circular saw: you can still lower the blade enough to clear the base and take a cut.I plan to use this to simply score metal for bending rather than do any heavy duty cutting; I have not yet had a chance to try this. The brazing on the teeth looks good so I'm not anticipating any problems unless it's that my cordless doesn't have the oompf to cut, but that would likely be more on the saw than the bladeWill report back if the blade doesn't hold up to use, but certainly looks reasonable.

This 3-3/8" diameter blade has 30 carbide teeth and is rated for 7,000 RPM while cutting metals (iron, steel, aluminum and copper). It is ideal for use with most cordless circular trim saws. The blade leaves a thin kerf to minimize material wastage and has laser cuttings to ensure dynamic balance.I used this blade to cut a series of cuts on 3/16" x 2" x 2" aluminum angle iron. There were no problems and the blade seemed to retain sharpenss while leaving smooth cut surfaces that required minimal post cut touch ups.Would recommend this for all those looking for a high quality product.

At first this thing cut like warm knife through warm butter. However within about thirty seconds the honey moon was over. It started slipping and balling down the motor to where it wouldn't cut anything. I've never had an issue with the saw until using this blade. My 2 minute job turned into 15 minutes of pure pain in the rear. I ended up using another cutting blade with much better results.

My husband has been using this 3-3/8" (85mm)-30T, Metal Working Circular Saw Blade, with an Arbor of 15mm and a 10mm washer, since December. He's found the quality to be decent. This saw blade has been a part of his toolkit for various projects, and it's managed to perform well across different types of metal. The 30 teeth design provides a fine cut, which is crucial for his precision work.Despite being put to the test on numerous occasions, the blade has maintained its sharpness and efficiency, a testament to its build quality. The inclusion of a 10mm washer for versatility in fitting different saws is a thoughtful addition, enhancing its usability.Overall, he's satisfied with its performance. It might not be the top-of-the-line in metalworking blades, but for the price and the tasks he's tackled, it's proven itself to be a reliable choice. This blade is a solid, cost-effective option for anyone needing a dependable tool for metal cutting projects.

Habe dieses Sägeblatt bisher nur für das Auftrennen von Alurohrverwendet. Das ging tadelsfrei, daher meine Kaufempfehlung.

this is a very sharp blade and goes though metal better than some other higher priced blades i have had, it cuts are accurate and clean, i have not had it lose a tooth or go blunt after several dozen mild steel and alu angles.

Es de buen material y corta bien el metal.Me ha llamado la atención el tamaño, ya que es más pequeña que otras sierras que tengo, aunque sirve para la radial que tengo.Estoy muy contenta con esta sierra.

Perfect for my hobby saw and the project i am building