dophee 20Pcs Brass Barrel Hinges, Small Cylinder Hidden Hinges, 4x20mm

Nice little hinges. Look and work great.

Nice hinge for a small box. There are no instructions on how to install these anywhere that I can find either on Amazon, internet or YouTube. These hinges require a substantial chamfer be cut into the lid that passes through the center of the hinge pin for the box to open properly. You may or may not like this look so it's good to know before you buy these. Here is how I installed them: 1. Offset two 4mm holes 1.5mm fro the back of the box. Hole alignment is critical so I actually drilled the holes in the side/rear of the box before I installed box top and bottom of the box so I could achieve that perfect alignment. 2. Glue the top and bottom on the box to covers up the holes so they are hidden. 3. Cut the top off the box. 4. Chamfer the back of the box top and bottom where the hinges get installed a minimum of 45 degrees with the chamfer extending at least to the center of the pin hole. 5. Glue in the pins with small amount of wood glue into the bottom of box. Rotate the pins so that they will bend straight out the back and insert into the holes in the lid. 6. Wipe up any squeeze out, then open and close the box a few times to make sure the alignment is correct and making sure it sits flat. 7. Prop the box slightly open and let the glue dry and you are golden! I also finished the interior of the box and the edges before installing these hinges so the glue wouldn't stick to the box. I did a light sanding after the glue was dry and finished the outside. Be careful not to sand through the back of the box and expose the hinges as there is only 1.5mm of material! Don't ask me how I know...

This is a good product. It's the first time I've used this type of hindges and I like the finished results. I have the 5mm by 25mm and they are very small but that's a good thing. Smooth operation.

These brass barrel hinges are decent for the price. I needed some hinges for a 3D printed box that I was making, and these worked well enough for it. The main issue I've had is that while some that came in the package have held up to hundreds of bends and have not loosened, others that haven't been used yet are very loose and wouldn't be able to hold open any sort of lid for a box. This makes me think that they may not be super durable. I have been using the ones that I felt were stronger out of the package, and those seem to be holding up so far.

Worked like a charm. Replaced failed pot-metal hinges on a tea box.

I purchased these 4mm hidden barrel hinges for a ring box. I scoured the internet for instructions and found none. Here is how I installed them. My box has a ¼” wall thickness. I drilled a 4mm hole in the center of the wall and 3/8” deep. The depth of the hole needs to match the length of the barrel from the pivoting pin to the end. Then I routed a 45 degree chamfer along the hinge side of the box on both the top and bottom pieces to allow the lid to open 90 degrees. The chamfer needs to remove the wood back to the center of the holes. Then I glued the hinges in with a little CA glue. I strongly recommend that you mock up the project on scrap wood as I show in the pictures. I also recommend using brad point drill bits to make sure you hit the exact spot for your holes.

Used one of these 4mm barrel hinges in a very small ring box. Used a 5/32” drill bit and installed with CA glue. The hinge was sturdier than expected for its small size. Happy with the results.

Great price, fast delivery and exactly what I was looking for to use in making small jewelry boxes

perfect for what I needed.

Perfect for my needs, great little hinges to go on the jewellery boxes, I have just finished making.

Erfüllt den Zweck

Arrived on time. I love them. Very easy to install and are very strong.

孫に踏切の遮断棒を作りたくて 買ったけど ダメでした。 丸い棒に付けれる 蝶番を探してこれを見つけたけど 使う用途が違い過ぎました。笑笑