Nilight - 10041P 2.5" Mini Projector Lens for H1 Bulb Headlights Retrofit, Custom Headlamps Conversion:Chrome Shround,2 Years Warranty

These projectors are awesome. So far I’ve retrofitted 2 of my cars; my first retrofit was done for my Sequoia and the second on my xB! The projector install itself is very simple; remove the old reflector, use the included adapters, and secure the projectors into your headlights. I like to test fit the lights on my car to ensure the cutoffs are level before redefining the lenses. Anyway, in both my cars I’m running 35W ballasts, and 5000k and 6000k(pictured) bulbs. As you can see; the cutoff is amazing. During the winter especially, most of my driving is done when it’s dark out and these projectors along with a set of HIDs just light up the road! I love the light output and feel good knowing I’m not blinding everyone by putting bright bulbs in a reflector housing. The high beams are great too. I cut off the included connector and used a deutsch connector instead which I find to be more durable but isn’t necessary. Overall, I’d say the quality of these projectors is solid. They fit well with extremely little to no modification and will really modernize your old reflector headlights.

For less than 30$ this is a steal. I did another retrofit with morimoto mini h1 7.0 and while it definitely feels more solid, this projector kit is great and I'll likely buy another set to have on hand before prices go up. tested solenoid about 50x each projector with a 9v battery and some spare wire before installing. shrouds screw in which is nice vs using jb weld and risking getting it all over everything. Fits perfectly on 9th gen civics (and should fit any 9006 low beam) with no cutting needed. I used an innovited 55w kit,h1 5000k bulbs, and wiring harness that matched my car wiring (9006) , some high beam splitters, and some adapters for the solenoid(in order to use factory high beams along with projector high beams) and I'm happy with it so far. From baking open headlights to completing the retrofit it took me a total of 3 hours (i painted mine so i let them dry overnight before resealing them). Will update if any issues arise. Hardest part was leveling the headlights. I made sure all tire pressure was good and car was level and used a brick wall to confirm them tightened down everything and sealed it up. The low beams are great but having two sets of high beams per side is really the main reason I wanted to do this. Using lasfit 9005 high beam leds paired with the projector hi/low beams and its amazing how much you can see at night. *update: swapped innovited bulbs for morimoto and they're much brighter and have more bluish color flicker. Also testing morimoto h1 bulb holders on these projectors and will update my findings. Update. Morimoto bulb holders work great with this. Couple months in with 55 watt hid and no issues. *update March 2026 everything is still in perfect working order no issues and have been using 55w ballast this whole time.

These projectors seems to be very popular with many questions from buyers so I'll try to be very thorough with my review. Purchase experience: I purchased these projectors 3 months ago, and at the time it was $39.99 (currently priced at $31.99), so doesn't sound bad at all for a pair of projectors + shrouds + mounting hardware. When my package arrived in the mail, I first inspected the contents and noticed that it was missing a set of shroud screws and also one of the lenses were chipped at the very edge (functions fine but cosmetically unappealing). I contacted the seller and they agree to send me a replacement lens and screws. I receive my second package.... and appears they send me an entire projector! No screws still. The problem is it's a different model projector and the lens is shaped differently - so it's no use to me. I decide to just call it a loss and continue with my build. Went out to the hardware store and source my own screws. I understand there are multiple vendors that sell under the same Amazon listing, and I don't see that vendor listed anymore. So chances are you may not get the same idiotic customer service as I did. Product quality: This is my first retrofit, and I'm sure a lot of buyers on here are too otherwise you'd buy the more expensive stuff. The projectors felt solid and very well made. They seem to be one of the better generic Mini H1 projectors on the market. Lens optics appear true without any distortion. Solenoids activate and deactivate normally. The cut-off shields seem a bit on the flimsy side but does not affect performance. Chrome bowls look very smooth and no gritty texture as I've seen in some other generic Mini H1 projectors. Fitment: This will vary from user to user but my retrofit process went smoothly. My vehicle is a 2015 Jeep Wrangler and I used my OEM 7" round headlight housings. They are very small in comparison to other modern vehicles, but I made it work by trimming the backside in order for the projectors to fit. The nice thing about the threaded shaft on the backside of MH1's is once you mount them, you can still make clockwise/counter clockwise rotation after your housings are resealed, so they are great for beginner retrofitters. I had to fine tune mine this way. I installed a Morimoto H1 4500k HID 35w kit into these projectors. They were not a direct fit because for some reason the projector bulb holes were slightly smaller than the bulb base. I had to shave some of the plastic from the bulb in order for it to fully seat, not a big deal. If you bought a cheaper HID kit with metal bases, they might fit directly as I've seen before. Performance: Everything has been working fine for the past 3 months. I'll update this review if anything changes but I don't anticipate that. The cutoff is pretty good - not as sharp as high end models but that is expected. There is a bit of blue color flicker at the edge of the cut-off line which gives it a nice effect. These projectors provide much much better beam width than my factory halogen headlights. On really dark roads I can clearly see off to the sides where there are sidewalks or ditches. With my old factory ones, they were harder to see. My video includes low and high beam, so take a look if you're interested. Overall: I am happy with the value of these projectors. Although I feel like I have already outgrown them and am ready to build my next set with better projectors. I gave 4 out of 5 stars mainly because of customer service. So if you don't want to deal with that, you can find other online retailers with similar price point but much better customer service.

TLDR; these projectors are junk, look a lot worse than stock halogens with a foggy lens, and retrofitting headlights is a very time consuming process. If you don't like them or get defective ones, then you have to take apart your headlight again just to get them out. Ruined a brand new pair of housings. -- Purchased these to retrofit a new set of headlights for 2000-2004 Subaru Legacy. It was a very time consuming and labor-intensive process to open the headlight assembly and install these, even as someone with a lot of mechanical and craft experience. Thankfully, minimal cutting was required and I just had to open a hole for the high beam wires. I marked the top-center of the projector lens so I could get it level and at the correct orientation. Carefully secured and tightened everything, triple checked my work. The way it attaches with the washers to the back of the headlight assembly isn't great, as the rubber gasket was too small and left a gap. The threaded base of the projector is a little too short, and the nut that holds it in place is such low quality metal that my needle nose pliers dug right into it and shaved part of it away. Okay, at this point it looks decent and I re-seal the headlights and begin the install of the HIDs. Spent a couple hours making a wiring harness. Get it all installed and finally working, then test the lights when it's dark. They look horrible. The right projector has a fuzzy blob as its output. The right projector has a jagged Z-shaped line that only goes 10ft out from my car then cuts off completely. It is embarrassing to drive like this. Now I test the high beams. It looks okay with the shutter open but not nearly as bright or defined as stock halogens in 20yr old housings. Frustrated, I switch the HIDs out with the stock halogen H1 bulbs, which I know are solid. Just as bad. I try to aim the lights and adjust the clip holding them in, nothing improves, and the clip that holds the bulb in is weak and it wiggles. It appears the left shutter is completely defective and isn't a straight line. I was hoping to get a refund and just switch back to the beat up stock headlights but there's no way I'm going through hours of labor just to remove the projectors from the headlight assemblies, to get $30 back. So that is part of the business model probably.

Installed these on my 2012 Jeep Patriot and the process was pretty straightforward. The cutoff is clean and sharp with a nice straight beam pattern, which makes a big difference at night. With the bulbs I paired them with, the brightness is strong and evenly distributed across the road. Definitely a big improvement over the stock halogen setup. The light output looks more modern and controlled, not scattered. Overall, really happy with how they turned out.

Good product. Big gripe though when I sent to check all my assemblies. each screw was stripped out like a gorilla tried to tighten each screw with an impact gun. All 6 screws (3 each) stripped out. Was able to get then out after 30 minutes and different type and size screw drivers, even had to bake them for a few min to soften the plastic. Support wanted me to send them back. But garentee the next set I'd get would be the same. Yes look good and easy to install. But even if you get them screws out..idk where you can but such a small screws to replace them. Paired with h1 HID set of bulbs. Tried a few combos. My assemblied wouldn't take an led, regal or slim style. Wouldn't take an h4 or h7 as the inlets were to small so I had to get the H1 HID . Once installed . Plug and play. You'll need an h1 adapter harness which is like 15 bucks. 3 pins were ben for the high beams.2 on 1 side, 1 of the other.. Had to bend then back with hopes they'd work. If you can handle fighting out stripped screws and having to reuse them good bang for the buck, if not I'd recommend another brand or one that cost a bit more. Used a 99 limited 4runner. Also remember to adjust the beams, seen some people saying you had to shim it? No there'd adjusted in your headlamps to bring up/ down . Side2side adjustments

Thi works well, I like it. Tacoma gen1 4WD

If you are comparing these to Morimoto Mini H1 projectors and questioning the performance of these, you are in the same boat I was two weeks ago. While the Morimoto's were easily affordable, I didn't see how there would be enough of a difference from these to justify the $80 difference. I bit the bullet and ordered these. Having never retrofitted headlights before I was anxious to see how these would project the light. Now that I have my the headlights in my car, these bad boys perform excellently. For HID's, I went with 8000k from a seller on Amazon and the color is wonderful. The only thing I can not attest to is the compatibility with anyone else's headlights. They fit perfectly in my 2002 Altima 3.5 which have a decent amount of space in them. These projectors are so compact that they should fit most headlights. For comparison, I recently drove a family members new Lexus and the projectors provide for great night driving. With that being said, these Nilight 2.5 Mini projectors and some good HID's (I paid $60 for the bulbs and ballasts) seem to perform better. The beam is wider allowing you to see off to the side with ease. This could be hysteria but they are excellent regardless. One absolute pisser at the time was that the screws holding the bulb mount to the back strip way to easily. Of the three on each projector, only two of the screws came out without issue. Be prepared to use a deep, thin precision flat head despite them being phillips screws (sorry I do not have the driver size in front of me at the time).

Muito bom

La entrega fue rápida llegó antes, el material es de buena calidad, yo lo utilizo con foco de alógeno de marca y la verdad me da muy buena iluminación, mejoro bastante, el corte de luz es bueno y no deslumbra a los conductores de enfrente, lo volveré a comprar, con calma buscare un buen foco led no cualquiera le queda o Xenon

👍

I installed these in my 2010 Xterra. They are absolutely fantastic for the money. The cutoff is very good with minimal chromatic aberration. The high beam motors are working well and there is plenty of light output. These are a massive upgrade to the stock headlights. There were no fitment issues in my case as well and no shimming needed like some people noted. Install these straight and make sure they are level. You can use the stock headlights aiming screw for the rest. Highly recommended. Hopefully they last a reasonable amount of time.

It's for to upgrade my headlight