CNC Aluminum Clip ons handlebar replacement for Ninja 250R 2008-2012 Ninja 300 EX300 2013-2018,Lower over stock,better over stock

Wow what a difference these are to the generac universal clips ons, these are super sturdy nothing flimsy about the metal at all

This has been mentioned before. The bars are great looking and mount to the ninja 250 really easily. The problems start when you are putting on your controls and levers. The bars are thinner than the stock ones. You will need to add shims, tape, or whatever to get everything tight so they don't move. Nothing is worse than pushing a button and having the whole control box slide out of place. The only control that tightened up without any spacer was the brake lever. Everything else didn't even come close to it. I used a single layer of an aluminum can for the clutch lever and 3 layers of bicycle tire for each of the control boxes. Even with drilling the holes for the peg on the control boxes left them to jiggle around. A little bit of a pain in the butt.

Fit awesome. Wish they would have come with the hardware for the ends though. Or atleast have the correct size written somewhere. I should have gotten the set with the plugs though cause they leave a bunch of ugly showing

They’re great! They fit the Ninja 300 no problem! I bought handle bars only. They DO come with hardware, so no need to buy extra bolts or anything. HOWEVER, The standard bolts for the bar ends are M8 x 30mm, which are too big for these! You can go to your local hardware store to buy M6 x 30mm! These fit these bar ends! The length can differ, since I use TST Industries’ handle bar ends.

Ordered these after seeing the pictures posted here, put them on my bike today and I gotta say the adjustability of these is actually pretty nice and more than I was honestly expecting. On the topic of bar thickness, yes you're going to need about one wrap around with electrical tape to keep your throttle from shifting or your clutch/break from also shifting. Other than that great bars, currently waiting on new grips to come in then will post pictures

I was worried about the fit of the controls after reading other reviews, but the bars i received where accurately machined barstock aluminum requiring no modification

Work as they are intended on my njnja 300. You will have to drill some holes for the controls of the bike and may want to use some tape to increase the thickness so they don't move as much. I've used them the last few days and they are doing just fine. Definitely worth the money for the amount of adjustment they allow.

Perfect for my 2014 ninja 300

ニンジャ250にジャストフィットで取り付けできました。作業時間は1時間もかかっていないと思います。 説明にも合った通り、スイッチのポッチっ分は削らないとつきません。また、削ったからと言って操作中に動いたりすることもないので支障はありません。 角度も左右きっちり均等に設定することができ、安心して使用できます。

EX250LにDIYにて取り付けました。ノーマルからの交換なのでバーエンドさえ外す事ができれば後は簡単ですかね。高さは2段階調整、ハンドル幅＆タレ角は固定です。ハンドルにはブレーキレバーなどを固定する穴がありますが全然違う位置なので自身でハンドルに穴を明けるかボッチをニッパーなどで切り落とすかですかね。切り落としは簡単です私は切り落としましたが特に問題は無かったです。ポンずけですのでハンドル交換だけなら30分掛からなかったと思います。（知識有り、グリップのはめ込みは除外）取り付けして１ヶ月ほど経過しますが特に問題はありません。海外からの発送みたいでしたが予定よりだいぶ早く届きました（10日ぐらい）梱包も中身が傷にならないようにしっかりしてました。ハンドルバーの穴が全然違う位置なので星4です。

Couple niggly points. The mount does not sit flat on the top of the triple clamp, as the triple clamp is not flat. Only out by a millimeter. The mounting bolts hold it in position well. The bars themselves are not quite the same diameter as the stock bars, so the switch blocks on both sides as well as the clutch mount needs a wrap of insulation tape to enable them to be done up tight. The new position of the bars does put you in a bit of a lean forward pose, but I find it comfortable. Over all, very happy.