TAILONZ Blue 100FT x 1/2" OD PU Air Hose Air Tubing Kit Air Line Hose

It is what it says it is

Very good kit, none of the push lock nuts leaked. The hose is flexible and the cutter that’s in the kit makes cutting hose a breeze and straight cuts.

I was able to set my system up in a single day with no leaks. The flexible pneumatic tubing is the best way I've seen (cost, value & safety) to install a compressed air system. I've mentioned safety because too many people have used rigid PVC pipe for their systems. PVC has a nasty habit of shattering while being struck while under pressure sending plastic shrapnel everywhere. The flexible tubing and fittings are the best and convenient way to set up your system quickly. Use the provided tubing cutter to give a good square cut that is necessary for leak-free junction. I have only three issues with this product: 1. They only provide two ball valves. I had to purchase another ball valve so I could have one for each manifold. The valves are necessary to drain water that accumulates in the system. 2. They only provide six tube clamps. That's simply not enough. You'll need to purchase a package of 1/2" tube clamps to adequately secure the tubing. 3. The teflon tape they provide is thin and won't seal well. It would be wise to purchase a spool of teflon tape from Amazon or at your local hardware store.

Great value in this kit. Thanks to smooth pipe interior and the minimal number of fittings needed to route the tube over a long path, this 1/2" system flows a decent scfm. I wouldn't choose it for running a large impact or similar air hog but for basic inflation needs, running an air nailer, using a blow gun etc this is a great system for distributing air around your shop. My only gripe is that the tube is pretty well set in the coil shape it was shipped. Very difficult to get it to relax so you can make nice neat looking runs. Maybe a 90 degree day would help but at 30f it is stiff and ornery. Even exposing the tube to a potent radiant heat source had little effect against the seemingly permanent coil shape. The kit comes with a couple of clips intended to secure the tube but they have nowhere near the holding power that is needed, nor are there anywhere near enough in the kit. Unfortunately Amazon doesn't seem to offer a quality cable clamp that fits this tube at an affordable price. The tube is right on 1/2" od. Affordable clamps marketed as 1/2" are actually less than 3/8. Ones that actually fit are crazy pricey. Give some thought to how you want to secure this tubing and bake the substantial costs into your calculations when considering this kit.

I bought this to run low-volume air to my electronics bench in the basement. I need to run a solder sucker that uses air to create vacuum. Sometimes I'll use it for a blow gun. That's about it. I have bigger lines run elsewhere in the house for larger tools. I was just getting tired of dragging my air hose across the basement to hook up the solder sucker when I needed it. This seems to be working a treat so far! I have PEX going from the basement to the upstairs garage (I know, not rated, but I've used PEX for air successfully for years.) I just cut into that with an NPT adapter. Threw a 1/2NPT to 1/4NPT bushing in that, then transitioned to the slip fittings from that. All I added so far is a drop for my bench, but I have a couple of tees in the line so I can add a drop elsewhere at a later date. When I pressurized the system, the only leak I had was the slip fitting at the top of my manifold block for my drop. I pulled it down and it ends up that it's the only joint I didn't add PTFE tape to. I thought I'd see how the factory-applied thread sealant worked. It didn't. Tape is cheap. Tape all your fittings. Otherwise, I'm extremely pleased, especially for the price. I couldn't have pieced it together with just the fittings I needed for less, and now I have leftovers for expansion! Time will tell how it holds up, but I have faith in it. It seems well-made.

For $70, this is quite a value. I've just installed this so I can't speak to longevity just yet. Installation was easy and straight forward even though there are no instructions. Make sure your threaded fittings are taped and tight, tubing cuts are straight and ends fully pushed in, and you should have no leaks. For a hobbyist's shop, this will do just fine. If I were to question any part of this kit, it would be the clamps. The screws are tiny and hard to use and I do question their ability to stay over the long haul. I will probably invest in some electrical harness clamps in the future. All other parts provided feel and appear robust.

Received as shown. People complain it doesn't come with this or that. If you look at the pictures it is everything as shown. The other thing people commented on was a mix of 3/8 and 1/4 fittings. The tubing is 3/8 OD and all pipe fittings are 1/4 npt as they should be. I couldn't really tell so I bought some 3/8/1/4 pipe adapters but did not need them.

Loved it!! Easy installation and I was happy it came with a cutter.

I bought whole set but got two pieces outlets one piece missing. the push in connector 1/2 size on other side only 3/8. The outlet cost $15.