DEWENWILS Wireless Light Switch Kit - No Wiring, 10A/1000W, 100 Ft RF Range, Remote Control for Ceiling Lights, Fans, Lamps

This was easy to install and came with clear instructions. Works great for adding an additional switch in another location. I installed the module in the box where the original switch was and mounted one of the wireless switches over the plate. The other wireless switch is on the other end of the house and both work great.

These are really good for DYI home design. I am not an electrician and do not want to be fishing power lines through the walls and ceilings. If you can install a light fixture you can install these - it is not completely plug-and-play (you still have to connect the wiring etc) but it is quite doable. Using these kits I was able to easily move the switches to better more accessible places - and even add multiple switches for a single light (one near an entrance and one near an exit). They saved a lot of work and have been working great for a few months so far. Excellent product.

This works really well. I'm using it with the switch about 9-10 feet away from where the receiver is mounted in the electric box. Installation was fairly straightforward, but it took a little effort to get the unit tucked up into the electric box.

The builder of our new unit in a retirement community used lots of pocket doors to save space in the rooms. Unfortunately, they were too cheap or lazy to put light switches where there were convenient if there was a pocket in the way. As a result, the bathroom light switch was about 18" inside the bathroom on a wall to the right of the right opening pocket door. This required fully opening the pocket door and reaching into the room to turn on the light. I was able to mount the remote switch just to the left of the door where it can be reached by opening the door about 6" despite the fact that this location is over the pocket of another door. Installation was straight forward once I resolved the neutral issue (below). Fortunately, the box where I mounted the switch is deep and there was room for this unit in addition to the multiple junction blocks and wires also occupying the box. It should work in a shallower box if the box is used solely for the wall switch being replaced by this unit but it is a little bigger than most single switches. Note that a neutral must be present in the box and the switch unit cannot be used to replace a "dangling' switch where a single two conductor (plus ground) wire is used to bring the hot line down from the fixture and to carry the switched power back to the light in the fixture. In this case, you will see both the black (hot) and white (neutral) wires from the pair connected to the switch. In this case, the electrical code requires the white wire to be wrapped with black or red tape to indicate that it is hot, but this was omitted in several places in our unit. The switch seems to have a loose internal connection since it will not work if the backplate on which it is mounted is not perfectly flat. I had to trim one of the plastic wall anchors to make it work consistently. I suspect that the battery contact may be at fault, but have not been able to check this. Thus far, it seems to work perfectly, but may fail if the mounting bends or warps. The wiring diagram seems to imply that the neutral must pass through the receiving switch unit rather than the unit being simply connected to a neutral. This is not possible in my wall box as there is a single junction block for multiple neutrals. I measured the resistance between the two neutral (blue) lines with a digital Ohmmeter and they appear to be connected together (R = 0.000 on the meter). I made a test jig from an old extension cord, connecting both blue lines of the switch unit to the neutral side of the cord (plug and socket) and connecting the brown line wire to the hot line from the plug and the brown load wire to the hot side of the socket. The setup worked in this configuration and I wired the switch into my box with both blue lines connected to the neutral junction block.

When we were renovating our home, we thought we had planned the lighting well and didn’t see the need for additional fixtures above the kitchen island. But once all the furniture was in place and the final details were finished, we quickly realized that the space felt a little dim. The extra lighting would have made a huge difference and add an extra decor, but since the ceilings were already closed up and painted, we didn’t want to go through the hassle of opening everything up again, hiring an electrician, and dealing with the mess. That’s when we came across this wireless light switch, and honestly, it was a game-changer. Installation was incredibly easy—no wiring, no complicated setup, and best of all, no need for a professional. Within minutes, we had the light above the island up and running. It was such a relief to get the added brightness we needed without any major renovations. Now, after a few years of using it, I can confidently say that it’s still working perfectly without any issues. It responds instantly, and we haven’t had any connectivity problems. If you’re in a situation where adding a wired switch isn’t practical or you just want a simple and effective lighting solution, I highly recommend this. It saved us time, money, and stress while giving us exactly what we needed.

Works well, easy to install. Works with our light fixtures with all LED lights installed. This wireless three way light switch was ordered to replace an existing three way wireless light switch that required at least one incandescent bulb be installed in the fixture or the lights would not turn all the way off.

Whoever ran the electrical in my house was not thinking! I'll save the long story!! This thing saved me a half a day of running wires! Iir took me 12 minutes to wire, 9 seconds to program and the big thing is that I jammed it in the nice hole between the light and ceiling and it worked perfectly!! It even worked in the room next door! I never knew anything like this existed before and I'm glad my electrician told me about them. I did zero research and thought for the cheap price, why not!! Going to buy a couple more for my mother so she doesn't fall down the stairs trying to turn on the hall light!! These guys didn't contact me or send me one for a review, I just bought it on a whim!!

Works great! I saw some say won't fit behind switch. I removed orig switch and cut rivets leaving only metal face to attach switchplate cover. Picks up all over including outside of line of site 20+ feet away.

Sencillo elegante y práctico

Funciona perfecto. Buenos materiales.

Excelente producto y super servicio del proveedor