Metra 95-5812 Double DIN Installation Kit Fits Select 2004-2019 Ford Vehicles -Black

Bought this for a 2008 Mustang (base model) and I was actually surprised how well it fit. There were detailed install instructions included for all the models mentioned in the listing and it was a pretty easy job to install it.I have never done anything like this before, and used this with an SJoybring Joy-W006 carplay radio and it fits snugly and looks like it was always supposed to be there.The one difficulty was some tabs that had to be removed to fit it in my vehicle. It says to just cut them off, but they are quite strong and required a saw to remove them. It wasn't a problem as such but wasn't quite as easy to do as the instructions made it sound.Overall, great value for money!

The media could not be loaded. Excelente choice when installing a new screen, i have a Ford five hundred 2005 and it fits perfectly, it has a universal set for diferent radios and screens

Worked perfect for my 2008 F250 super duty radio replaced with Amazon double din stereo.

Well it does not come with the black plastic on the sides. This are a metal pieces. dont know if it is good or bad. Havent install it yet. But is not what the pictures shows on the amazon.Update: metal did not fit my car. Stead of cutting and make them for i reused the one i had. Not a big deal thou. Some cutting and bending will make it work.

I mean it’s works

This review is strictly for a 2008 Ford Explorer, the product may be perfectly suitable for other vehicles.I've used Metra dash kits for many years now, and have always been pleased with their quality and finish. In this case, I am very disappointed. This kit is for both single and double DIN installations. I am installing a double DIN enonon G2104 head unit. It is clear they tried to make this one product work for a wide array of vehicles. As such there are modifications which are required to make this kit work with your specific vehicle. I'll try to describe each issue.1. The dash kit when properly assembled just doesn't fit properly into the dash opening. There are gaps between my dash trim, and this install kit's face plate. There is absolutely no way to correct or fix this.2. The kit requires you to cut tabs off of the kit for the explorer installation. You'll need to not only cut off the tabs, but sand down the bracket where the cut was made.3. For the explorer install spacers are included and required. The spacers are problematic. They should snap in place, but they are too loose, and tend to fall out as you are attempting to secure the kit to the dash.4. The face plate requires you to recess your radio into the dash. The kit's face place sits on top of your head units face plate, and pushes your head unit backward into the dash recessing it. Now this doesn't sound bad until you see it installed, it looks like a hack rather than a clean installation. If you have a deep head unit, you may even have issues getting it to fit in.5. Because the face plate covers over the head units face plate, units with controls near the edge will be blocked by this kit's face plate. On my unit, the USB port, SD card slot, infrared window, and a few other items we inaccessible with this kit. Also if you have knobs, the kit may not fit at all. The knobs on my unit are close to the edge, and since the kit needs to cover a bit of the units face plate, the knobs wouldn't even fit through the opening in the kit. If you have a motorized front face, there is no way this kit will work. Rather than covering the head unit's front face, they should have made the kit to allow the head unit's bezel to pop through the kits face plate.6. Be wary of using the included screws, they are very long, and may interfere with the functioning of your head unit. You would be better off getting shorter screws.Overall I am seriously disappointed with this kit and would not recommend it for a 4th gen explorer installation.

Wouldn’t fit in my 06 Explorer. Saw another reviewer saying he had to cut some piece off for it to fit in his 08 explorer and it worked, wish this was stated in the instructions. Pieces are definitely not meant to be cut off and was a clever work around.

Aligns with the screw holes of a 2005 Ford Focus and looks great for a double-din install. For this install, 4 tabs are in the way, especially for the top right screw. I snapped off that tab to insert the screw.