Cloudray Co2 Laser Rotary Attachment Rotary Axis 2 Axis CNC Laser Rotary Attachment with Nema 23 2-Phase Stepper Motor(Chuck-4 Pin)

one of these came with my Laguna MU laser. it works quite well, but you have to put a weight in the glass to make sure it has enough traction to actually rotate the glass. what i use is a 1-1/4" half inch drive socket wrapped in duct tape. but with odd shaped glass it would be better if the non-driven rollers were replaced with a centering cone. it works well with beer glasses (mixing), 30oz tumblers, Coffee cups, old fashion glasses, and margarita grande glasses however, a brandy glass needs a centering cone.

These rotaries are missing one very important element - a clip that goes into the opening of the cup you are engraving to hold the cup steady. They chatter and move, ruining your engraving. There are so many others out there withy the clip it is amazing these do not come with them, or an option to add one does not exist. There was a guy who made an add on clip but now he makes a boss jr rotary for over $600 so you can't buy the add on clip kit any longer. How hard would it be for these manufacturers to add a cup clip? really?

I need a rotary jig to broaden my abilities. Will this unit work on a OMT 80 laser running light burn app with a ruida controller The picture shows the connection point on the controller.

Heavyweight to keep from moving around. The orings on the drive and guide wheels are kinda slippery allowing work to slip have to drive it slowly.

It was supposed to come with the connector and cord. It didn't. It came all beat up and I had to return it. I'm going to try to buy it again. Wish me luck!

How many steps (pulses per rotation)? Shouldn’t it be the same every time?

After minor adjustments it worked right out of the box. It even had the correct plug on the end. It was essentially plug and play for me. I have an older Full Spectrum Laser Pro with 2 phase stepper motor. Would highly recommend anyone looking for a rotary attachment.

Not a horrible accessory for your laser engraver; be prepared to tinker. I own a Full Spectrum Laser, and Full Spectrum sells an overpriced, dysfunctional rotary axis. Then they charge you to take it back. This device is worlds better, if you take charge and fix its minor problems: - Make sure you buy the right motor configuration. For the FS P Series laser, you need 2 phase motors (4-wire). - You will need a connector to match your laser. For the FS P Series, that's a GS16-4 aviation plug. - You will need to configure your laser to match the resolution of the rotary axis. 720 steps/inch seems right. - The clamp on the vertical adjustment was installed backwards so it wouldn't clamp - take it off, flip it, put the thumbscrew in the right way. - All the screws were loose, so align the drive wheels and tighten things up. - Rubber feet add 3/4" to the height of the unit; that's 3/4" wasted. Take off the feet and replace them with felt pads. - The unit was missing an O-Ring, M3X63 fits. M3x63 Buna-N O-ring, 70A Durometer, Round, Black, 63 mm ID, 69 mm OD, 3 mm Width (Pack of 25) . Ships from China. Unit arrived in a week with no damage.

Tolles Projekt

È tutto in alluminio... Ottima qualità ed è molto preciso

Nicht kompatibel mit einem Top Wisdom Kontroller und damit für mich unbrauchbar. Aufgrund dass diese Rotationsachse aus China kommt, kostete mich der Rückversand 100 Euro.

Das Gerät war leider nicht so gut verpackt und musste erst mal komplett neu eingestellt werden - das sind nur ein paar Schrauben und ist schnell zu lösen. Ein paar abgeplatzte Stellen im Lack sind auch zu verschmerzen. Der 2-Phase Schrittmotor wird bei mir mit einem DM545C Treiber betrieben und das geht auch prima. Was mich allerdings gigantisch nervt ist das keine Dokumentation dabei war. Die Informationen sind teilweise in der Amazon-Artikelbeschreibung zu finden, teilweise in der Suchmaschine des Vertrauens. Der Schrittmotor hat keinen Aufkleber mit den Daten und eine Typenbezeichnung konnte ich auch nicht finden - das wäre aber ganz hilfreich um den Treiber korrekt einzustellen (Stromaufnahme). Wenn er dann läuft (den Treiber habe ich jetzt nicht anpasssen können) ist alles super.