Boker Plus Tek-Lok Adapter

Based on other reviews across the net about this little mod, I figured it was exactly what I needed. I'm not a fan of hanging nylon belt loops on knife sheaths, and this handy device replaces that AND gives your BK2 more ways to be attached to you or your gear.There are no instructions with the Tek-Lok, however it doesn't take much Googling to find various ways to install it on your sheath. The toughest part of putting it on my BK2 was the removal of the 3 rivets that hold the nylon belt loop to the Kydex sheath that comes with the knife. By using a small sharp wire cutter, you just carefully nibble at each of the 3 rivets until you can pop them out. Took me about 10 minutes total, then it was on to the rest of the install.To install the Tek-Lok to the BK2 sheath, you need to remove the 4 screws of the belt loop holder from the rest of the sheath. A phillips screwdriver will do that easily. Now, figure out which position you want to install the Tek-Lok (keeping in mind if you want it to be installed for left or right handed pull of the knife out of the sheath). I wanted my knife to install scout-style (horizontal instead of vertical) and I used the middle row of holes on the Tek-Lok. Using the hardware provided with the Tek-Lok, insert the threaded grommets into the Tek-Lok from the inside (clasp open) and then line up the grommets with your BK2 belt loop holder and use the included screws to tighten. You will not need the 3 rubber grommets that come with the Tek-Lok. I actually used one of the grommets to push against the backside of the threaded metal grommets to give me some traction when tightening the screws. Now that you're done with this part, just re-install the BK2's belt loop holder piece back to the BK2 sheath and you're ready. Tip: throw a little drop of Loc-Tite on the threads of the screws on the Tek-Lok so it doesn't come loose (Loc-Tite is not included with this product, you'll have to get it from your local hardware store).The Tek-Lok also comes with 2 snap-in belt loop sizing spacers. These snap into various positions inside the Tek-Lok so you can use this device with various sizes of belts and straps without it feeling loose. Take both of the spacers out and you can fit the Tek-Lok on up to a 2" webbed belt or smaller padded backpack strap. Or, put the spacers in and this will fit your knife snugly on even the thinnest uniform belt.One last feature to mention is the additional clasp lock that keeps the Tek-Lok closed and prevents it from accidentally getting opened up if bumped. The two release latches on the side of the clasp are very strong and they should stay in place, but the rotating clasp lock ensures that these two latches cannot be pressed in and come unlatched. Very nice little feature. Just use your thumb to roll it out of the way and you can quickly undo your Tek-Lock clasps and remove it.I use the Tek-Lok in the scout-style position to attach my BK2 to my belt or to my shoulder straps of my various backpacks and bail-out bags. Now it's right up on my chest and ready to pull down in a split second. This position also makes it great on my belt so the knife doesn't hang vertical and get in my way if I have to squat down or sit. The composite material that the Tek-Lok is made out of is extremely strong and I can't imagine breaking it unless I fall off a cliff while wearing it, or smash it with a hammer.Best mod ever for your Becker BK2 and worth every penny.

I bought this item to attach to my CRKT Bear Claw so that I could wear the knife horizontally. Unfortunately this does not match up with the holes in the plastic sheath. It is, however, very well built and I'm positive I will find another tool to use it with.I gave this product 4 stars because I can see that it is of great quality, but took away one star only because it didn't fit the tool I purchased it for. But, such is life.

The knife is the Boker Fritz, which is 5.5 inches long and included a kydex sheath and neck chain. Purchased the mini tek-lok to mount the sheath horizontally on my belt. Had trouble deciding on whether to get the mini or standard sized tek-lok....not knowing the width of either mounting hole panels or where the holes would hit on the sheath. Well the mini has 9 holes in a panel 1 and 1/2 inch by 1 and 1/2 inch square. The mini came with no instructions, the hinged plastic unit and three (3) grommets, and three (3) screw units. First I checked to see how the unit would fit on my Wilderness Tactical 1 and 1/2 inch wide belt. Perfect fit. Next I checked the alignment on the unit with the holes on my sheath: the holes on my sheath are 1 and 1/2 inches measured center of hole to center of hole. So at best the sheath could only be mounted to ONE HOLE on the mini tek-lok. Just for giggles I mounted the unit to the sheath at one hole and no matter how tight I set the screw the sheath would swivel on the unit. Do NOT over-tighten the screw or it will strip the threads!! Next I drilled a hole in the sheath for a second hole/mounting point. If you do this:remember to chose a drill bit the exact size as the screw (that came with the tic-lock) to ensure snug fit upon tightening. Oh, BTW I chose to mount the unit so that the swivil part was at the top of my belt and the snap section at the bottom of my belt....if it comes unsnapped (the snap is quite secure, I'm just a careful guy) it will still be wrapped around the belt. Next slip the screw thru the hole in the sheath, slip the grommet over the screw push the other reciever part of the screw thru the mini and twisting the screw join both parts of the screw. Here is a problem: the screw has two parts as I said, the screw and a reciever part. The reciever part needs a tiny (and I mean TINY) allen wrench (Problem: allen wrench not included with tek lok), the screw is a phillips. With the phillips you can get it sufficently tight. I used lock-light also on the screw. With this unit in hand now I will be purchasing a regular sized tek-lok for my other knife sheath. I'm happy with the Mini tek-lok and for what I intend to use it for it rates 5 stars in performance.

I received a small Boker neck knife as a Christmas gift and bought this to mount the knife on my belt in stead, but only two of the six holes in the sheath actually line up with the holes in the tek-lok at any given angle. It appears to be well made and sturdy, but it's obvious whoever designed the two items were not in communication with each other.

this is my first tek-lok ever bought. now i wished i had started using them many years ago. i had purchased a countycomm.com large breacher bar with their kydex sheath for it and used this on the sheath and it is awesome. very versatile and compact for all that it can do. it does take a moment or three to figure out how to screw it to the sheath but once you got it it made perfect sense. if you carry a large and heavy knife or tool on you belt or pack this is a must have because it will never break (unless you purposely try to) and you can adjust the tension of it.

I love this little adapter, its genius. I would have never bought the Boker Gnome knife if this adapter wasn't available. I was able to attach it to the Boker knife's sheath and carry it on my belt, daily. It has the adjustability to mount to the sheath in different ways to fit your carrying needs. I'm not a neck knife kinda guy so this adapted what was suppose to be a neck knife to a belt sidearm sorta carry option. Def a must have for the Boker Gnome or any small knife you wanna make work for your needs.

Love these clips

El material se ve y se siente muy resistente.Fácil de montar y desmontar, sin tener que sacar el cinturón.A pesar de que este broche solo se puede abrir con dos dedos y algo de fuerza tiene un seguro para evitar poder abrir el broche.Tiene una cuadricula con 9 perforaciones, lo que permite colocar el cuchillo ya sea vertical, como horizontal, zurdo o diestro.queda bien en fundas de sistema molly, de mis otros cuchillos.Dentro lleva dos separadores que se ajustan al ancho del cinturón que quieras usar.quedo perfecto en la funda de mi cuchillo BK2, convirtiéndolo de una funda con una sujeción pera mi gusto muy mala, en un cuchillo versátil y cómodo sencillo.Tal vez compre otro para mi cuchillo SOG Kiku.Lo recomiendo plenamente

Seriously overpriced as no different from the standard large ....... but even more expensive

¿Por qué han canviado la foto del producto en el transcurso de mi pedido? .No es el mismo modelo.Lo recibo mañana.Me temo que tendré que perder mi tiempo en devolverlo.Cuando lo reciba, haré otra reseña tras analizar el producto.Lo quiero para un bk2 companion y repito según la foto no es el producto que pedí. No se si valdrá. O si me están tomando el pelo.

2本挿しシース自作でベルトループもカイデックスだと重みに負けそうで不安がありましたのでこちらを購入。ベルトの左に斜めに固定で邪魔にもならず良い感じです。保持力も問題無しです。