4pcs Hall-Effect Joysticks Replacement for DualSense PS5 Controller, 3D Analog Sensor Wheel Thumb Sticks Rocker Module Replacement for PlayStation 5 Controller

These were just as described. Unfortunately, I lack the skill to install them myself and wrecked one of my son's PS5 controllers 🙁 The good news is I have a friend who works in the electronics industry. He was able to install them in the spare controller, and they ended up working out perfectly. There is no more stick drift, and the response time seems to be better than the factory controller.

Have two dualsense controllers with jitter on the right sticks. I had heard hall effects would correct the problem but didnt want to waste the high cost at the moment. And after having the same issue with ps4 controllers years back, I knew the level of work it would take to change these. I bought the tiny film with potentiometers first to try out. Those where a lot cheaper and it was a lot easier to just put a little solder on top of the original stick contacts. Tried those on my dead ps4 controllers and as I thought, it didnt do much. With those tiny film potentiometers you adjust on one end but the other side of the travel gets messed up. Those where more luck than a guaranteed solution. After a year finally saw this hall effect ones on a reasonable price and decided to buy them. Be advised this is a complicated replacement to do. The toughest part is removing the original ones from the controller. Controller can be opened with a quick internet video. But desoldering the old one takes A LOT of patience. If your up for the challenge it'll fix your dead ps5 controller for sure. Just take your time a dont rush. Once you get the original one off its easy putting the new one in and just taping the solder points. To calibrate them after, just go on the internet and look for a video. Its easy and again, PATIENCE is the key on removing the old one AND calibrating the new one. From a 50 dead zone setting on apex were down to a 0. Oh and I only replaced the bad one. The other joystick on the controller was fine. If it also goes bad along the way I'll just do the same.

My son has had his PS5 for two years now. He has been dealing with stick drift since about 3 months after starting playing. At first I could go in and clean the wipers. Then I bought replacement analog joysticks and just put those wipers in. I finally broke down and purchased these Hall effect joysticks. I should have done this from the start!! Easy enough to swap out. I have very little experience with soldering but was confident enough. Definitely use high heat and a broader iron tip. Probably don’t spring for the cheapest iron like I did. And don’t let the solder points combine. They actually do need to be separated, cleanish looking. Plenty of helpful videos out there to show you different methods for removing the OEM sticks. After replacing them, my son says the drift is gone and it is even more precise control. For a few dollars you can have an awesome functioning controller again!! Just go for it if you are on the fence.

After calibration from the online site, my aim is still 1:1 on cod like the potentiometers however NO MORE DRIFT! The sticks are bit easier to move so it took a few games getting used to. All in all 10/10 (1.67 K/D resurgence sweat)

Well, the install was great. Did some testing and it was good. Well, when we played diablo 4, the R3 on the joystick collapsed and quit working. Other than that, it fixed the drift, and felt alot more premium. Just be careful when buying

These are good for the price. The only issue I’ve noticed is that the right analog stick has a slightly rough feel when moving up and down. It’s not terrible, but it can get annoying at times. Another thing is that even after calibrating, there’s still a small amount of stick drift that won’t completely go away. That said, it’s nowhere near as bad as the OEM sticks that came with the PS5 controller, and it’s much more tolerable than the originals. Overall, I’m satisfied with them. If you plan on installing these, make sure to do your research and have some basic soldering skills. You don’t need to be a pro, but having some experience will definitely help.

This would be five stars but some (about five) pins were bent. I was expecting these to work but not without issues, however these gave me no issues (yet). I did a circularity test before, after and at the end of the installation so that I could see and keep track of the results. Circularity is better than oem and we're easy to calibrated. Played for three hours and had no issues. They dont come centered so calibration is mondatory.

Great sticks. This repair is fairly advanced. If you have the equipment and skill to remove the original sticks, these go on easy peasy. The trick is getting the original sticks off without damaging anything. You MUST run the config app on them or they will seem borked at first try.

Setup is pretty easy if you know what you're doing. If you don't there's this great app called YOUTUBE it will teach you how to install and calibrate the sticks. Oh and it has less tension in the springs less stiffer than than the OEM so you'll probably have to lower your sensitivity if you play fps. On Call of duty I run a 5 and 5 min input deadzone works smoothly no more drifts!

Didn't realize we needed more tools to replace. So we returned.

3 of the 4 were damaged internally. The joystick wouldn’t move properly causing drift. I had to remove them and get new ones. Check them before installing to save yourself a headache. Also, they wouldn’t calibrate properly.

Works great

Product is good quality. The install is not easy, I found the best method was to get a heat gun and hot swap the old joysticks out and slap these in all in one go. Good luck.