Invision TV Wall Bracket Mount for 24-60 Inch Screens, VESA 100x100mm up to 400x400mm, Tilts Swivels & Extends for Flat & Curved TVs, Includes Spirit Level, Weight Capacity 36.2kg (HDTV-E)

Excellent product. Very sturdy (when you pick up the package it really has some weight in it), well designed & neat-looking piece of kit which is fantastic value for money. Attaching it to the TV: This was purchased for an old Sony Bravia TV with odd (200x150mm) VESA dimensions. I clarified with Invision CS (who were very well-informed & responsive) before puchasing that it was compatible & simply used the back-plate without the additional 'wings' supplied; cinch to fit & lines up perfectly. I wanted to use the longest spacers provided since, due to the - outmoded - TV design, the backplate covers all the connectors, so purchased some longer (50mm) M5 screws to allow sufficient clearance. The 25mm screws supplied would have been fine were it not for this. There's a very good selection of other options too so you should find what you need in the pack. Attaching it to the wall: My TV weighs about 17-18kg - for a 32" it's a bit of a clunker due to its age & I bought this for my kids' (6yo) playroom so I deliberately over-specced the bracket to cope with the potential 'abuse'. Until I started drilling I hadn't realised that the walls were thermalite (breeze-block), i.e., a bit like the solid sponge-type stuff that's used for flower-arranging... I exaggerate slightly! I therefore opted to trade-up on the fixings & swapped the 80mm long coach screws provided for 100mm & used 2 x rawlpugs in each hole - the ones provided at the back & new ones purchased at the front to give sufficient purchase. As with those provided, the screw heads are hex so I was able to tighten these with a socket - I doubt you'd manage to do this with a spanner let alone a screwdriver so worth considering this before you embark. The result: a very solid, secure connection, tested out (as suggested elsewhere) by each kid swinging on the bracket - at maximum extension too - w/o any mishaps. (I've obviously banned them from doing this again now there's a TV attached to it!) TV is dead easy to attach once you've fitted the bracket to the wall but it is a 2-person job - 1 to guide, the other to lift. Instruction booklet - though typeface could be a little bigger - is easy to follow & has good graphics too. All-in-all, an excellent product. Seems a little counter-intuitive that you'd entrust your £1,500-worth of Sony/Samsung/LG to something that costs £25 but I really think you'd struggle to find better at any price. * I obviously didn't test this but would be confident the wall & TV would 'fail' first!

Whilst some might say "It's a TV bracket, surely they're all the same?", they'd be wrong. First of all, the instructions include pictures AND words. It makes it significantly easier to then understand what you're supposed to do. If you're a competent DIYer then you won't even need the instructions, as it is so straight forward. There are two stand-out features of this product that I doubt are even mentioned anywhere in the spec / listing, but are so incredibly useful: 1. You can adjust the level of the TV with two screws AFTER you have put the bracket on the wall. Yes, we all want to get the bracket on straight the first time, but if you catch the brick and the drill goes slightly off (or you're just not very good at measuring level) then you will be very, very pleased for the range of motion to adjust the level on the back of the TV mount. Such a simple idea but brilliant. 2. When you want to mount the TV the bracket that is on the back of the TV 'slots' onto the wall mounted bracket. It is then held by two screws (the same two screws that can adjust the level (see point 1). This doesn't sound much but have you ever tried to do up two screws whilst balancing a TV on your head if you're doing the job by yourself? It is nearly impossible and risks you dropping the TV. Therefore, to have it where the TV slots on and then allows you to just steady it and do up the screws at the back without the fear of it falling off is again, a simple yet brilliant bit of design. The bracket itself; sturdy, solid, well made and easy to pull out / adjust where you want the TV. It comes with wide variety of screws, spacers, washers and anything else you may need, so regardless of the size and shape of your TV you can get the mount to fit on well. I'm sure there are cheaper mounts out there but you'll be kicking yourself when the TV isn't level and / or you've dropped it trying to put it up because the mount didn't have the two features above. Furthermore, is it really worth ordering another to save a few quid when I can hand on heart say this is the bracket that does everything you want it to and a whole lot more.

Really good all round will buy this again as another few needed Pros Brilliant bracket, and solid Good idea with the built in cable tidy. Use on all size tv vesa mounts Good hinges which, holds the position really well Good tilt angle hold which, hold the position well Not too bad to fit at all would have been better with supply of anchors rather than, the wall plugs but was fine. Cons For any novice diyer, make sure your holes are bang on as, no movement is given in the holes compared to others. Instructions are not great for attaching the extension arms but not hard to figure it out. Cheap spirit level supplied - we used our own quality one as, the plastic one supplied wasnt cut straight so giving inaccurate level The pros really do out weigh the cons as being picky but only as having the right equipment and knowledge

This is a very sturdy, well built bracket. I bought it hang my 40" Samsung TV on the kitchen wall. The kit comes with a selection of VESA/Machine screws to attach your TV to the hanging plate (more on that later) and 4 rawplugs and 80mm coach bolts for bolting the bracket to the wall. There are 3 holes at the top of the bracket, 3 at the bottom and one in the centre. The instructions recommend to use the 4 corner holes if attaching to a solid wall or the 3 vertically centrered holes for a plasterboard wall. My wall is a plasterboard wall and luckily there was a stud timber where I wanted the TV positioning so the bolts are securely attached. Note that the coach bolts supplied are 8cm long so make sure if you are putting into a partition wall that it is deeper than this otherwise the bolt will come out the other side! If your TV is a 100 or 200 VESA set then you do not need to attach the separate extension arms, the backplate has the holes already there. The arms are only required if you have a TV requiring VESA 300 or 400 spacing. I did not use the supplied spirit level as it is a very cheap plasic one which I would not trust to be totally accurate. I used my own level for installation. Also I would recommend a socket set for screwing the bolts and the various nuts on the bracket as the spanner supplied would be too much like hard work (and hurt your hands) and it looks as though it would not be up to the job anyway. A socket set makes installation so much easier. If your bracket is a fraction out of level, when you add a TV to the bracket it is even more noticeable. A nice feature of the bracket is that you can adjust the rotation of the TV clockwise/anti-clockwise up to 8 degrees so even if you are slightly out, add your TV, put your level on the TV edge and then simply rotate the TV. Bingo! The plastic covers around the arms are very handy for routing the cable(s) through to keep them all tucked nicely inside. So, why the 4 stars? One point - I have a 40" 2017 Samsung UHD TV (not curved). According to the TV instructions you need to use on their 40-49" TVs 45mm M8 screws to attach the bracket backplate to (when using the Samsung supplied spacers). Invision supply a whole host of machine screws for attaching your TV but the longest M8 screw supplied is 40mm which is not long enough to attach the plate to the TV. I had to buy these separately. Invision do state that if you contact them they will supply the required fittings but I could not wait around emailing and waiting for them to post me 4 bolts. As Samsung are one of the main TV brands I would have thought that Invision should have supplied M8 45mm bolts as standard. All in all a great bracket and really pleased with the purchase despite having to source my own TV machine screws. Recommended.

Very good product that is flexible for the different support layouts. Movement in all directions is simple and easy and the included spirit level makes it easy to get the television level. Only minor hiccup is that the power cable and aerial cable are too short to be routed neatly, but those should be easy to overcome. Cannot fault this product and would recommend to all.

My 6th tv bracket I’ve had to put up, and this was as simple, sturdy, and well built as the other 5 at a quarter of their price. Plenty of fittings supplied with it, and it doesn’t need the extra diagonal brackets if the tv is 100 - 200 vesa. Comes with small wrench that didn’t actually fit the bolts for the wall (I’d recommend using a socket wrench for this anyway), but it also came with magnetic spirit level and a hdmi cable which I wasn’t expecting. You’ll need a Phillips screwdriver (which isn’t included) to install the backplate to the tv, and the fastening screws go stop it coming off the bracket. You can shift the tv about 10mm in a clockwise or anti clockwise direction when it’s installed to balance it if the bracket isn’t completely straight. I marked the bracket holes to drill, but had to drill into a solid rock wall (old fashioned cottage) and the wall killed my drillbit which made me drill a bit wonky by a few mm, which would usually drive me insane, but it was a very simple fix swivelling the tv up a few mil into position. It’s solid on the wall and the arm is tight so it won’t move freely, but not too tight you’d struggle to move it. The bracket although hidden by the tv has a cover to go over it to hide the bolts and wires trailing through. Would definitely buy again for the ease of use and quality.

Extremely well put together and feels very high quality. Easy to mount on the wall and gives great viewing angles.

Very impressed wit this TV wall bracket. Once fitted it works brilliantly, and is extremely sturdy and flexible. The kit comes with a variety of screws and spacers to accommodate for different TV sets. It took a bit of trial and error to figure out the right combination for my Samsung TV, but got there in the end. Installation was a bit tricky with 1 person. I'd definitely recommend getting yourself a helper to hold the bracket in place as you figure out where you want it positioned. You will also need a 10mm drill bit if you wish to use the supplied fittings. The bracket extends out a fair way from the wall, and for large/heavy television sets this will put a lot of force on the fixture (leverage etc). For myself, I do not plan on extending the bracket, and I also have a small/light TV set, so the supplied fittings were a bit overkill for what I needed, but I fitted them nevertheless. The supplied screws/bolts do not have screwdriver slots in the end - you will need a spanner or a socket set. I used a spanner and it was a mission - took about 30 minutes just to get the bolts in the wall. A socket set would make this a lot easier. Needless to say - once fitted, you could probably hang an elephant off them - they are extremely sturdy indeed. One thing to watch out for when fitting the bracket - it has a feature which allows you to adjust the tilt of the television. This needs to go at the TOP of the bracket. I mistakingly positioned it at the bottom, which resulted in me then having to take the bolts out to turn the thing round and re-fit it. Most annoying - the product would benefit from an arrow indicating which end of the bracket is which. All in all, this is a quality piece of kit for a very reasonable price. I will probably purchase another one soon.