Tiger Tool35mm Wheel Bearing Greaser for use with Polaris, Jansen Motorsports 35 Millimeter Wheel Bearing Grease Packer for ATV, UTV, and SxS, 1.003.003

Works pretty well on my ‘22 Sportsman 570. One thing I did have to swap was the grease zerk because the fitting on my grease gun hit the axle and wouldn’t lock on to the fitting. Easy swap, it uses a standard SAE fitting

Do NOT waste your money and time on the others. I bought one that was $20 cheaper, it was a poor design and put grease everywhere other than in the bearing. I then bought another brand that was about $5 cheaper. It didn’t fit the model that it said it fit, and was of poor quality. I then bought this one! The taper design is perfect and the quality is top-notch! Grease went into only the bearing. No comparison at all to the others. It is also the only brand that came with good instructions, in English!

BUY IT U WONT REGRET IT. WORKS GREAT!!

Sent me a used one with blue grease in it, all banged up. Like others experienced, zerk fitting too close to shaft to allow grease gun fitting to go on straight, causing grease to leak between zerk and grease gun fitting. Should come with 45° zerk. Now I have to buy one.Edit: although the item came used, it was not the fault of Tiger Tool. In fact they reached out and made things right. I’m very impressed with their customer service.

Works perfect, I've bought others tools before this one and endup returning them, because the center hole of the tool would not fit through the axle splines. I've contacted the seller before ordering asked them a few questions and he knew what I was talking about. Very good tool.

Worked great on my 2015 Polaris Ranger 570 midsize crew. Easy to use for a novice. The front bearings are a different size that the rear bearings, so two different sizes are needed for my Ranger.

It did its job fine. but i had to take a angled zerk fitting from another item to be able to use my grease gun. the product came with a extra rubber ring that for me was in peaces. and also the condition of the tool itself looked like it was washed with nasty well water and then had spots on it before it was put in the bag. used it.. did its job. going to buy a differnt set and throw this one away after i get a better tool set

Purchased and used on a 2019 sportsman. Nice to see grease oozing out the way it should. Did not get stuck on, followed directions

I spent much time searching and reading reviews on these types of bearing greaser tools. I found the majority of reviews for the Tiger brand to be good and decided to purchase. I ordered the 35 & 40mm tools for my 2015 Polaris Sportsman 570 SP. they work perfectly and include an extra O ring with each tool. Very happy with the tools.

Well built and pleased it came with a extra O ring. I lubed the O ring before using so did not need to use the spare.It's a snug fit. Takes a bit of wiggling to go on and take off but well worth it.It did a great job of pushing out the old grease and moisture. Took me more time to gather my tools than to do the job.I installed a 45 deg. grease zerk for my LockNLube grease gun coupler to fit properly.The 2012 Polaris Sportsman 500 HO needs a 40mm greaser in the rear and a 35mm (with a 7/8" hole to fit over the axle shaft) in front.

This thing works amazing! Cuts out so much of the work of having to remove front driveshafts to gain access to the bearings. Fit perfect for both my 2006 Polaris Sportsman and my 2005 700. Little on the expensive side for a tool you will rarely use but the money you'll save on your wear components running without grease is worth it! The quality is top notch as well. Nothing cheap about these things!

Bearing greaser showed up used and spareo-ring is broken, not a big deal as long as it works but would’ve been better if I didn’t pay full price for a used product, should have a 45° grease fitting aswell to help clear axle shaft

Worked perfect. Way better than the cheap knockoffs