ANNKE Universal Junction Box Mount Bracket for Bullet Dome Turret PTZ Security Cameras Outdoor Waterproof Aluminum Wall Ceiling Mount Hide Cables

Great product, well made a must when fitting external cameras....

Well made product and should last. The only thing stopping the 5th star is, if you are not using the gland for cable entry and are using the back for wall mounting. The threaded screw cap in the back closes the hole where the gland was, but there is no rubber bung to replace that screw cap. So have some silicone to seal the cable entry from the wall to the junction box to prevent damp and water ingress.

Compatible with TAPO C720 camera

It a good sturdy unit however I purchased it to use with Annke bullet cameras. When I tried to position camera to fit none of the holes would line up to secure camera. It might suit dome/turret CCTV cameras.

If you are mounting your camera on a rough surface like brick work, this junction box makes fitting easier and neater. It is quite large but very solid. Be aware that unless your cables are large diameter you will need to use silicone sealant to ensure a water and insect resistant installation. Not especially cheap but easy to fit your Annke camera.

Bought his to fit one camera in my new set but it wasn’t suitable and had to be returned as the inlet for the cable is enough,pus and has no reducing pieces so would t be waterproof! Annke camera cables are only about 6mm whereas this cable entry is around 20mm. Sorry! It’s a shame as it’s an excellent quality product.

4 stars cos 1 of the screws snapped in the mounting plate, but fits the Tapo c720 which I know there’s alot of people struggling to find 1 that fits

Back box for round dome cameras. As this goes, it pretty robust. It even has a wire retainer for the lid, so it can't make a leap for freedom, like some of the cheaper versions do... if you know, you know, right? Has grommets for the cable Passthrough. And a gland type compression fitting for the cable in the side.

I spent days looking for a junction box to mount an Amcrest Floodlight camera (ASH26-W), of which Amcrest was not helpful at all. It recommended a standard bell round junction box but the camera is 5.5" OD, so that huge diameter difference would just collect snow in the winter. This Junction Box has the following details missing from the product description: -Outside Diameter = 5 5/16“ -Base and Cap Material = Coated Aluminum -Front Seal = white foam on most of the front face -Rear Seal = black foam almost the entire back face -Ports = 2x 3/4“, 1 on the back, 1 on the side -Back Knockout Cap = white coated metal with rubber O ring -side conduit connector = grey plastic with rubber O rings (did not check fitment, not going to use it). -sealing between main body and cap -drainage on the side port, cannot mount that upwards (even with a knockout Cap on) My plan is to mount the camera on the wall and route the wires through the rear port, so I'm going to chuck the conduit connector in the bin and move the knockout Cap from the rear to the side. The only thing I wish all these damn companies would do is add a full drawing of the product.

Great materials and perfect shipping time

This box is built like a tank. It has thick metal and a nice paint finish to protect from rust. I have two complaints, however. My first complaint is that this Annke junction box isn't large enough to fit an Annke VC800 dome camera. My other complaint is that the included conduit connector isn't big enough for 3/4" conduit even though the connector goes into a 3/4" knockout. I can't even fit 1/2" conduit into the included conduit connector. If I do use liquid tight flex conduit I will throw away the included conduit connector and buy any standard 3/4" liquid tight conduit connector which I have already verified fits perfectly into the 3/4" threaded knockout holes. In case if anyone else isn't using conduit and needs to fill the knockout, you can buy any threaded 3/4" knockout cap like here https://www.amazon.com/Greenfield-PP3BR4-closure-plug-bronze/dp/B07TZTY7S9. This is a really good box as long as you bring you provide your own knockouts and conduit connectors. I'm astounded by the build quality. I expected less even with a $25 box. The screws holding the box together will not fall out, there is a metal strap to hold the box and cover together, the screws to mount the box are heavy duty and have rubber grommets, even the machine screws provided to mount the camera have threadlock. Rumor has it Annke is related to the high cost Hikvision company and this box makes me think that's true since it's exactly the same as what Hikvision offers and the quality and included hardware is impeccable. I just wish I could mount my Annke VC800 dome cameras to it. I'll end up putting the Annke C800 turret cameras on these boxes.

Très déçu. Incompatible avec la caméra NC800 malgré ce qui est indiqué sur le site.

It is not wide application, I had to drill extra holes to make this work for my PTZ cam