3D Printer Glass Bed Upgraded Borosilicate Glass Build Plate 310x320x3mm for Creality CR-10S Pro CR-10S Pro V2

I have one complaint. Amazon shipped this glass only in the manufacturers packaging and it was not taped shut. Luckily it was ok considering the pizza-like box was open.The glass on the other hand is protected by white foam and peel away plastic top and bottom. I'm using this on my Two Trees Bluer Plus because I have not been happy with the levelness of the PEI bed that came with the printer. The glass is fine as long as you coat it with either hair spray or glue stick.

I did not relize just how much my old bed was messing me up. Trying prints 4-5 times before getting one that sticks. Some I could not even get to work. Ordered this and put it on. Leveled the bed and such a difference. Not a panicia but able to print things much easer now. Worth the money. It is a little thinner than stock.

I am replacing my original CR-10S glass as it mysteriously developed a bow. Using a machinist straight edge and feeler gauges, I found that the center was .008" lower than the edges. Doesn't sound like a lot, but .008" equals 0.2 mm, which is the thickness of of a typical layer. So prints would stick around the edges, but not in the middle. I have a BLTouch, but it can't compensate for this much un-eveness, apparently. I checked the new piece of glass and it is flat to at least .002", or a quarter of a layer. That should be no problem with or without BLTouch. I gather from other reviews that some are getting non-flat glass. Would definitely recommend checking the piece you get before the return window closes. I figured that might happen and was going to keep returning them until I got a good piece. Got lucky on the first one.

This product worked perfectly. My print bed was wavy, so I was unable to get anything to stick to it properly. Slapped this bad boy on there and all of my bed adhesion issues were gone. The clips rattle a little bit, I ended up just removing the metal handles. I do use magic goo, I suppose it's out of habit. But when you use it, it will leave swirls on the glass which will transfer to the printed object, I have no problems with that. When the bed is hot it is extremely hard to pull of right after printing. If you wait for the bed to cool it the print comes right off.

Good item. It would have been a bit better if it had come with some way to attach it. They did provide spring clips, but they get in the way of the extrusion head on some prints. If it had sticky tape on it, I would have given it 5 stars.

I have a CR-10S Pro V2 and tried 2 different kinds of textured plates and tried blue tape but could not get petg to stick. With this bed and glue stick I have gotten my first good petg prints ever. 255 microswiss nozzle, 90 bed. I am thinking of moving away from pla to petg entirely because most of my prints are workable components and not decorations. It's easy to switch build plates back and forth but this glass is thinner than the stock plate so you have to adjust the z offset and I used a couple pieces of old credit card to shim the glass under the stock clips.

It looks great for a build plate. And I suppose it works great as a material that doesn't expand/contract throughout a large temperature range. But it is hardly able to remain flat across the surface. I generally adjust my starting nozzle height to one paper's sheet thickness above the bed across the surface. If I do so with this glass near the four corners, I get a gap near two sheet's thickness in the center of this glass. That is not acceptable. I get better results surface flatness with the use of a thicker mirror as my build plate.That being said, it doesn't provide good adhesion on its own without using glue or hair spray. I can do the same with a cheaper mirror as my build plate if I have to revert to the use of a solvent for adhesion.

Being relatively new to 3D printing I am always willing to learn and try new things. This has been a really great product as of date. Seldom does a something work as claimed, this does. Ability to print without the addition of any adhesive whatsoever is a huge benefit, for me at least, quick turn around, zero clean up of surface are others. Sticks solid when hot, releases without tools when cold. Even small prints with tiny footprints hold firm during any and all bed jarring that may occur.It is also thinner and lighter than the mirror panes I was using to great success as well, but with much more work and effort to get good results. Thumbs up all around for this one I love it!