Question 1

Do you have to unplug this while bike is turned off? Will it drain the bikes battery if no usb devices are connected?

Accepted Answer

I had one hooked up and just a few days it ran a brand new battery dead.  Suprised me, i thought it would last nonths but no. Several days staying hooked up, it will 100% drain your battery.  Do what you want though.

Question 2

Will this work with the output from a bicycle hub generator?

Accepted Answer

Lol... that’s a... unique idea. It should work it you can supply a constant 12V which will be quite difficult under the scenario you propose unless you have some kind of capacitor bank or something similar that will deal with voltage spikes and ... well, the inconsistent power that you’ll likely be generating. Plus you’d need an existing female SAE to plug this into. I don’t see how this would be any better than simply using what you have to charge a lithium battery bank with a usb output.

Question 3

Does the lights stay on the whole time like i want to hook it to my battery on my bike and monitor why i ride

Accepted Answer

Hi Mike, the meter times out after 10 seconds after you plug it in. Pressing the button will make it run for another 10 seconds. I drive a KLR without an idiot light to warn me of an alternator failure so I recently purchased a voltmeter for my bike from Datel.  http://www.bikemeters.com/cgi-bin/webshop.cgi?config=ent-datel&uid=alvvbwvi141086408221&command=link--home.html  If you buy yourself a single pole double throw momentary on switch you can wire it so that pressing the button before starting will connect the voltmeter directly to the battery for open cell voltage check. Upon releasing the button it will read off of you accessory buss (key switch) whenever the bike is running for checking alternator output. With this switch setup the meter will turn on and off with your key with the button released and will come on with the press of the button when the key is off which allows you to measure resting battery voltage without any load such as your headlight and running lampsHere is a link to a sample switch. https://www.superbrightleds.com/moreinfo/dimmers-and-switches/led-indicator-push-button-switch/1201/It's a lighted switch but you don't have to use that portion of the circuit. Just connect C-1 (common) to your voltmeter, NC-1 (normally closed) to your hot buss (anything powered by the key switch for the bike, and NO-1 to you battery. Use a small gage wire like a no. 22 and you should probably add a fuse at the each power tap to protect the wires and meter. A 1 amp one would be fine.Hope this helps! Kindly,Denise

Question 4

Is the precise voltage displayed by numbers or only red, yellow, green lights as status indicaters?

Accepted Answer

On the unit I have it is on the money, I checked it against my Simpson meter I use for work i just go by the numbers  ALSO I found all the equipment from Battery tender works well, there are some oddities as of stupid Calif regs.but you must by the CORRECT one. if not sure CALL Battery Tender in FLA, they will set you straight. New for 2015: Try a phone call! you will be amazed that somewhere there is some one who will SPEAK to you and help you out on most anything. THAT'S American type service .

Manufacturer	Battery Tender
Brand	Battery Tender
Model	081-0158
Item Weight	0.01 ounces
Product Dimensions	5.5 x 1 x 5 inches
Item model number	081-0158
Is Discontinued By Manufacturer	No
Exterior	Painted
Manufacturer Part Number	081-0158
OEM Part Number	900589
Special Features	Connects to 12V Battery
Safety Rating	Não Aplicável
Amperage	2.1 Amps
Voltage	12 Volts
Wattage	10 watts

Sobre nosotros

Servicios al cliente

Atención al cliente

Acceso Regional

Legales y políticas

Social

Obtén la aplicación

Battery Tender Quick Disconnect USB Charger Adapter - Easily Charge Mobile Devices with 12V Vehicle Battery on The Go - Perfect for Camping Our Outdoor Adventures - 081-0158

Detalles

Descripción

Presupuesto

¿Tienes una pregunta? Mira lo que otros preguntaron

Reseñas

Preguntas comunes