EATON PT18M-V-K Accell Core Programmable Timer, 120 V, 5, 10, 15, 30, 60 Min Off, Ivory

It works beautifully, was easy to install, arrived quickly and was packaged well.

Good quality upgrade with a better style to it.

I ordered two of these and they both work fine. The lights are all green color. The light on the vertical off button on the right side remains on continuously. All lights are very small and bright enough but not annoying. For me they are just right. This switch unit does NOT use a neutral wire, which is a big plus. So it will replace any standard switch, even with no neutral in the box. There are three wire leads, one for the hot/continuous power, one for the switched power to the device, and a ground. The leads are about 6 inches long and it comes with wire nuts. The unit fit nicely in my box and it is not too large. I think it would fit fine in any standard box. The ivory color on this cooper switch matched the ivory Leviton brand toggle switch next to it perfectly. FYI I have this wired to a motorized duct damper in the bathroom HVAC duct in the attic which is 115 volt powered closed, and springs open when not powered, so I can close the air conditioner vent over my tub when I shower. Very happy with the whole set up.

Pros...- Multiple colors- No neutral required- Easy to install- Timers are accurate- Looks nicer than expectedCons...- When installed it needs to be perfectly flush with your face plate. Anything other than light pressure on the sides of the switch from the faceplate will cause the buttons to stick or not work at all. This seems like a design flaw to me as the front of the switch seems to shift a bit with pressure instead of being a solid unit. Overall it was annoying more than anything. Note that I have a GE switch that is similar and is totally solid... just didn't come in the color I needed so I went with this one. I'd recommend the GE switch over this as it's a nicer unit and cheaper, but it only comes in white.Example of my issue above: switch was not perfectly flush, maybe a mm lower on the left side (hardly noticeable, honestly). When I put on the faceplate and screwed it down with even moderate pressure, the 30 and 60 min buttons would not work as they were jammed/stuck in place. If i took all the pressure off of the screws and let the faceplate float, they would work. I ended up jimmying it around quite a bit and loosing the screws anchoring the switch to the box so the switch was floating. Still ended up having to shim the bottom and keep the faceplate screw loose on the bottom to ensure the 60 minute button would be clickable AND trigger off when the time was up.

This switch works for 3 of the settings but one setting doesn’t work at all. It comes with directions that say you can program it, but my husband could not get that to work. He messed with it for quite a while and finally said he thought maybe it was defective as it did not work as indicated. We bought to prevent our renter from leaving the exhaust fan on literally day and night. 🤦🏻‍♀️😑

Thing went in easily and works fantastically. The black is perfect for my bathroom's "theme". This went on a circuit for the exhaust fan, replacing a twist countdown timer, which also work great, but those seem to burn out after only a couple years. Hoping these modern push button ones will last longer than that. Only down side would be increments - I am not sure 5-10-15 [30,60] min should be the first three defaults, but these units do have at least one programable key, so as long as you know, that is fine. one button shut off is nice, and contrary to other reviews, in looking at the instructions that come with the timer switch, this one can be forced permanently on as well.

When I originally installed this for the fan in my bathroom, the fan turned on after I turned on the power, and none of the buttons did anything, so it was always on. I thought it might have been broken or the fan too large for the switch to power it, but I got a solution from another reviewer that I'm now signal-boosting. If you run into this problem and don't have a neutral wire in your box, just connect the neutral (white capped) wire on the switch to the two ground wires (the switch one and the wall one) in the wire cap, so that all 3 are connected together. This fixed the issue, and the switch now works great.

No cover came with timer switch.